Question: Use the Finite element method to develop the stiffness matrix for element 2 of the steel cantilever beam structure shown in Figure Q1. The

Use the Finite element method to develop the stiffness matrix for element

Use the Finite element method to develop the stiffness matrix for element 2 of the steel cantilever beam structure shown in Figure Q1. The elastic modulus is 200 kN/mm2 with a thickness of 1 unit and Poisson's ratio of 0.3. Assume plane stress conditions 36 kN 0,3 3.5, 3 4 3. 0,0 3.5, 0 FIGURE Q1

Step by Step Solution

★★★★★

3.43 Rating (153 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The stiffnes... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (2 attachments)

6366ed3dda4eb_241155.pdf

180 KBs PDF File

6366ed3dda4eb_241155.docx

120 KBs Word File

Students Have Also Explored These Related Civil Engineering Questions!

Use the finite element method to approximate the solution to the boundary value problem Carefully explain how you are setting up the problem. Plot the resulting solutions and compare your answer with...

For the structural steel plate structure shown in Figure P12-6, determine the maximum principal stress and its location. If the stresses are unacceptably high, recommend any design changes. The...

Develop the stiffness matrix for a fictitious pure shear panel element (Figure P4-46) in terms of the shear modulus, G, the shear web area, Aw, and the length, L. Notice that Y and v are the shear...

Evaluate the stiffness matrix for the elements shown in Figure P6-3. The coordinates are in units of inches. Assume plane stress conditions. Let E = 10 106 psi, v = 0.25, and thickness t = 1in. (a)...

Evaluate the stiffness matrix for the elements shown in Figure P6-6. The coordinates are given in units of millimeters. Assume plane stress conditions. Let E = 105 GPa, v = 0.25, and t = 10 mm.

The tapered cantilever beam AB shown in the figure has a solid circular cross section. The diameters at the ends A and B are dA and dB = 2dA, respectively. Thus, the diameter d and moment of inertia...

For the beam problem in Example 8.3, the boundary conditions required that the resultant normal force vanish at each end (x = l). Show, however, that the normal stress on each end is not zero, and...

12. Consider a simply supported beam of length L = 1 m subjected to a uniformly distributed trans verse load p0 = 100 N-m. The cross-section is rectangular with width w = 0.01 m and height h = 0.02...

Calculate the deflections Î´B and Î´C at points B and C, respectively, of the cantilever beam ACB shown in the figure. Assume M0 = 36 k-in., P = 3.8 k, L = 8 ft, and EI = 2.25...

Show that the Airy function: solves the following cantilever beam problem, as shown in the following figure. As usual for such problems, boundary conditions at the ends (x = 0 and L) should be...

Sandhill Co. sells office equipment on July 31, 2022, for $22,430 cash. The office equipment originally cost $77,870 and as of January 1,2022, had accumulated depreciation of $36,830. Depreciation...

In other words, according to your informed thinking on what you have observed, in what ways was the leader's behavior impactful or was not effective, and why do you say so?

Assume that the initial stock price is So = $ 1 0 0 . You would like to hedge a long position of 2 0 call contracts ( 1 0 0 shares per contract ) with 2 5 0 days to maturity anda strike price of $ 1...

. The Charter of Rights and Freedoms, part of Canada\'s constitution, was drafted broadly, with the expectation that its provisions would be interpreted by case law. Why do you think the drafters...

The COMMON law system is the system of law that courts follow in the U.S. It was borrowed from the British system and still exists in most countries that were once part of or still are part of the...

Mention a few food safety practices you will exercise when dealing with ready-to-eat foods?

Lower of Cost or Net Realizable Value Example: Cane Co. uses FIFO and the perpetual method to account for inventory. At year end, the unadjusted inventory balance is $100,000. The company determines...

A copper sphere of 10-mm diameter, initially at a prescribed elevated temperature T;, is quenched in a saturated (1 atm) water bath. Using the lumped capacitance method, estimate the time for the...

Choose two of the groups in Exercise 9.4.36 or 9.4.37, and determine whether or not they commute by looking at their infinitesimal generators. Then verify your conclusion by directly computing the...

Discuss the effect of a uniform horizontal force in the direction of the horizontal bar on the swing set and its reinforced version in Example 6.9.

For each of the following tridiagonal systems find the L U factorization of the coefficient matrix, and then solve the system. (a) (b) (c) 013 212 110 1067 00-6 0-45 210 1100 0231 0011 0041 2310 1100

3. Uncertainty Avoidance. The degree to which groups will encourage members to feel threatened by unknown or ambiguous situations and develop beliefs, institutions, or rituals to avoid them.

2. Societal Cynicism. This dimension represents an apprehension or pessimism of the world. Caring about societal affairs only brings trouble upon oneself and kind-hearted people usually suffer losses...

1. List and describe the various subjective elements of culture.