Question: Use the virtual work method (graphical method) and determine the horizontal displacement at C (ACh) and the slope at B (0g). B ET kN

Use the virtual work method (graphical method) and determine the horizontal displacement

Use the virtual work method (graphical method) and determine the horizontal displacement at C (ACh) and the slope at B (0g). B ET kN El O ACH=106.67/EI,6g=20/EI O ACh=80/EI, eg=40/EI O ACh =80/EI, Og320/EI O ACh=106.67/EI , eg=40/EI

Step by Step Solution

★★★★★

3.26 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Use the virtual work method (graphical method) and determine the slope at C (0c). El is constant. 8 ft 4 k/ft 10 ft O Oc=0 O ec=800/EI O ec=266.7/EI O ec=533.3/EI

Determine the slope and displacement at C. EI is constant. Use the conjugate-beam method. Mo = Pa a

Determine the slope and displacement at C. EI is constant. Use the moment-area theorems. Mo = Pa A B

Rashid is a 55 year old Indonesian citizen settled in the island of Penang under the Malaysia: My Second Home programme since 2012. Rahid is a well-known author who likes the Malaysian food and...

Miss Muriel comes to you for advice in February, 2021. Last year 2020, was a year of considerable change and turmoil for her. Her job in Waterloo, Ontario, with X Ltd , a Canadian public corporation,...

goal ciple of virtual wark, also referred to as the unit - load method, provides a method for detormining the slope cement at a specific point in a structure. For a truss, the method of virtual work...

nal virtual unit load acting on the truss joint in the if , n is the internal virtual normal force in a truss aused by the external virtual unit load, is the external acement in the desired direction...

Problem 2 : Virtual work method ( 2 4 pts ) For the beam shown in Figure 2 , use the method of virtual work to determine based on El: a ) The vertical displacement at point \ ( \ mathrm { D } ( \...

1. Calculate the sample size needed given these factors: one-tailed t-test with two independent groups of equal size small effect size (see Piasta, S.B., & Justice, L.M., 2010) alpha =.05 beta = .2...

For the shown beam, a . Determine the reaction at the supports. The support at B is a roller and C is pinned. Consider EI to be constant throughout the beam. ( 5 Points ) c . Determine the slope and...

What is the shutdown price when all fixed costs are sunk? What is the shutdown price when all fixed costs are nonsunk?

Phillip Sheridan frequently flies between Washington, D.C. and Raleigh, North Carolina, and as the distance is short, the airline uses turboprop airplanes. He often has a choice between flying on a...

Use the Intermediate Value Theorem to show that the equation - x 3 4 x 1 = 0 has at least one solution on the interval ( - 1 , 0 ) .

A single circuit 3 phase transmission transposed line is composed of four ACSR 1,272,000 cmil conductor per phase with horizontal configuration as shown below. The bundle spacing is 45 cm. The...

Fault analysis: Consider the following five-bus power system (A-Y phase shifts are negligible. Prefault voltage is 1.08 per unit). Figure 2: A five-bus power system. Gener- ator G1: 100 MVA, 10 kV,...

the intensity of light from a lightbulb is 10 w/m^2 at a distance of 0.50 from the bulb. what is the intensity across the room at a distance of 3.5m?

The synchronous generator shown in the figure below is operated at its rated apparent power (100 MVA), 0.95 pf. lagging, and 5% above rated voltage. Determine the subtransient fault current if a...

Outliers tend to ___ the value of the correlation coefficient while restricting the range tends to ___ the value of the correlation coefficient. Answer options: increase, decrease, or no effect

Determine the vertical movement of joint D if the length of member BF is increased by 75 mm. (Hint: Apply a vertical load at joint D, and, using the methods of Chap. 6, compute the force exerted by...

Determine the slope and displacement at point B. Assume the support at A is a pin and C is a roller. Account for the additional strain energy due to shear. Take E = 29(10 3 ) ksi, I = 300 in 4 , G =...

Determine the vertical displacement of joint E. For each member A = 400 mm 2 , E = 200 GPa. Use the method of virtual work. 1.5 m A JO 45 kN 2 m 2 m

Using the method of virtual work, determine separately the force and the couple representing the reaction at A. 240 300 m 300 m 240 N 960 N 1030 900 600 mm

The uniform bar AB has weight W. If the attached spring is unstretched when = 90 deg, use the method of virtual work and determine the angle for equilibrium. Note that the spring always remains in...

Determine the vertical movement of joint C if the length of member FG is increased 30 mm. (Hint: Apply a vertical load at joint C, and, using the methods of Chap. 6, compute the force exerted by...