Question: Using Excel, draw the shear force and bending moment diagram for the given beam with distributed load values of 1 l b f t ,

Using Excel, draw the shear force and bending moment diagram for the given beam with distributed load values of 1lbft,20lbft,50lb/ft and 100lb/ft. Let L=10 feet. Indicate the value of max moment and where (x value) the maximum moment occurs.
Using Excel, draw the shear force and bending

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

You are a project manager. You are estimating cash flows of a potential project that requires investment of $250,000 in a machine, including installation cost, and $40,000 in working capital which...

Q:

1- Draw the laod carrying mechanisms for the Gerber Beams shown. (30p). 2- Draw the shear force and bending moment diagrams for the given beam by using the moment distribution method. (Assume that El...

Q:

2 - Draw the shear force and bending moment diagrams for the given beam by using the moment distribution method. ( Assume that E l is constant along the beam ) . a , b , c , are the last three digits...

Q:

0 Draw the shear force and bending moment diagram of the below beam. Include key values on your diagrams such as peak values and distances. w= 5 kN/m M = 6 kN.m 4m CU hp 27 M 14C Partly sunny

Q:

Allu The three span solid slab cast monolithically with the supporting RC beams shown in figure IV is175mmthick, supports a variable load of3.0KN/m2, has25mmcement sand screed floor...

Q:

EXPERIMENT # 2 : Analyze and draw the Shear force and Bending Moment Diagram for cantilever beam using SAP 2 0 0 0 . Objectives To determine manually the reactions and draw shear force and bending...

Q:

a: b: b) Draw the bending moment diagram. 150 100 gz N 50 -50 A a b B 1 2 3 4 6 7 8 -100 -150 A: B: a: b: 9 10 10 11 & + 12 - -

Q:

g) h) 5 KN 50 mm 20 mm 150 mm 40 mm 2 kN 200 mm 5 kN 1 kN Three forces are applied to member ABD as shown. The cross-section is a hollow rectangle with 20mm height and 40mm width and a wall thickness...

Q:

Given a distributed load w = 6N/m is applied to the beam, that is support by a wall A. A clockwise-moment M = 12N -m is applied to point B. If a = 5m, draw the shear force and bending moment diagram....

Q:

Property Density Yield Strength Ultimate Tensile Strength Poisson Ratio Shear Modulus ASTM A710 Steel AA 7075 2.81 503 572 7.8 585 620 0.29 80 Young's Modulus 205 Dimensions Side bar (C-Channel) =...

Q:

In the beam shown below, the Uniform Load W applied along the entire length of the beam is 19 kN/m and the applied load at the tip of the overhanging is 32 KN. (a) Calculate the reactions. (b) Draw...

Q:

In evaluating the selling prices for products at her part-time retail job, Susan asked her supervisor how the company sets its prices. Her supervisor told her it applies a steady markup percentage on...

Q:

Do you prefer to buy a name brand or a store brand? Are there some products for which you prefer store brands and other for which you prefer national brands? Be certain to comment on at least one...

Q:

Item Skipped Item 10 An insurance company must make payments to a customer of $11 million in one year and $7 million in five years. The yield curve is flat at 6%. Required: If it wants to fully fund...

Q:

I. Scenario - 1 You have completed the course on Corporate Finance. Based on the whole course and contents, elaborate what kind of knowledge and skills you can apply in your day to day operations a...