Question: What will be the electrical output with this force if we have a four active gauges, each with a nominal 1 5 0 resistance and

What will be the electrical output with this force if we have a four active gauges, each with a nominal 150 resistance and a gauge factor of 2 and a 10 V power supply?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

Example 2 : A strain gauge has a nominal resistance of 1 2 0 and a gauge factor of 2 . 1 4 . If it is used in a quarter bridge with the other resistors being 1 2 0 and with a supply voltage of 2 V ,...

Q:

Example 8 . 7 A hollow - cylinder load cell of the type shown in Figure 8 . 3 4 ( b ) has an outside diameter of 1 in . and a wall thickness of 0 . 0 4 0 in . It is made of aluminum with a modulus of...

Q:

PROBLEM 2 . 3 ( 2 0 Points ) A cantilever beam is subject to unknown normal and tensile forces. The normal force is directed downward and has magnitude F . The tensile force has magnitude 1 0 F ....

Q:

A diaphragm pressure sensor employs four identical strain gauges to monitor the stress it is subject to. Specifically, the four gauges are placed in directions as shown in Fig. Q1(a) so that only Rg2...

Q:

help asap please Q1. (12 Marks) A load cell is installed as part of a crane-safe load monitoring system. Four active atrain gauges are included in the load cell, cach with a nominal resistance of 120...

Q:

the strain gauge B is NOT in same direction to force F, rather it is perpendicular to force F (transversal strain), so you have longitudinal strain for strain gauge A and transversal strain for...

Q:

the strain gauge B is NOT in same direction to force F, rather it is perpendicular to force F (transversal strain), so you have longitudinal strain for strain gauge A and transversal strain for...

Q:

( 2 0 pts ) Consider the cantilever beam subject to a downward load force at its outer end as shown in the figure below. Two strain gauges ( a and b ) are attached to the top of the beam where they...

Q:

2. (20 pts) Consider the cantilever beam subject to a downward load force at its outer end as shown in the figure below. Two strain gauges ( a and b ) are attached to the top of the beam where they...

Q:

A metal bar strain measurement is performed as shown in Figure Q3 below. Two strain gauges A and B are glued as shown in Figure Q3. The dimension of the metal bar: Width: w-50 mm, thickness 1-40 mm,...

Q:

George bought a shop in October 1998 for 290,000 and used it in his business until April 2010, when he gave it to hisfriend Harry. The market value of the shop at that time was 570,000. Harry ran the...

Q:

Calculating the Predetermined Overhead Rate, Applying Overhead to Production At the beginning of the year, Debion Company estimated the following: Line Item Description Amount Overhead $641,200...

Q:

The following is the current balance sheet for a local partnership of doctors: \ table [ [ Cash and current assets,$ 8 1 , 0 0 0 , Liabilities,$ 7 8 , 0 0 0 ] , [ Land , 2 3 6 , 0 0 0 , A , capital,...

Q:

Aninvestment offers $6900 per year for 19 years, with the firstpayment occurring 8 years from now. If the required return is 3percent, what is the value of the investment? O $81,019.80 O$86,468.23 2...