Question: Why is the enable secret password displayed differently from what we configured?

Why is the enable secret password displayed differently from what we configured?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

The following is a condensed version of the comparative balance sheets for Zubin Mehta Corporation for the last two years at December 31. Additional information: Investments were sold at a loss of...

Q:

Packet Tracer - Configure Initial Switch Settings Part 1: Verify the Default Switch Configuration Part 2: Configure a Basic Switch Configuration Part 3: Configure a MOTD Banner Part 4: Save...

Q:

Part 1: Verify the Default Switch Configuration Step 1: Enter privileged EXEC mode. You can access all switch commands from privileged EXEC mode. However, because many of the privileged commands...

Q:

Topology Objectives Part 1: Verify the Default Switch Configuration Part 2: Configure a Basic Switch Configuration Part 3: Configure a MOTD Banner Part 4: Save Configuration Files to NVRAM Part 5:...

Q:

How many Fast Ethernet interfaces does the switch have? 2 4 How many Gigabit Ethernet interfaces does the switch have? 2 What is the range of values shown for the vty lines? 0 , 4 , 5 , 1 5 Which...

Q:

Lab 1: Introduction to Packet Tracer Lab 1: Introduction to Packet Tracer Total Marks= 10 Objectives of this Lab: The goal of this lab is to become familiar with building topologies in Packet Tracer...

Q:

IFT 366 TCP/IP & Routing Lab 1 Configuring the router via the CLI (the very basics) Purpose of this lab : get an overview of some of the tasks that are done to configure a typical router. We will use...

Q:

Go back to Router> 1. Enter privileged EXEC mode. Router>enable Router# 2. Enter global configuration mode. Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z....

Q:

Cisco Networking Academy Mind Wide Open Lab 1.5.2: Basic Router Configuration Topology Diagram 192.168.1.0/24 192.168.2.0/24 192.168.3.0/24 PC1 Fa0/0 S0/0/0 DCE S0/0/0 Fa0/0 PC2 ----- R1 R2...

Q:

1. Enter privileged EXEC mode. Router> enable Router# 2. Enter global configuration mode. Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# 3....

Q:

System Security - Lab 3 (10%) Configuring AAA Authentication Objective/Purpose I AAA (authentication, authorization and accounting) is a service used in networks to centrally manage user account....

Q:

Suppose a spinless particle is bound to a fixed center by a potential V(x) so asymmetrical that no energy level is degenerate. Using time-reversal invariance prove ? 0 For any energy eigenstate....

Q:

Describe the two concepts that influence materials handling choices. Give an example of a product that would be appropriate for each.

Q:

Problem 1 7 - 3 Lee Development Company has found a site that it believes will support 7 5 homesites. The company also believes that the land can be purchased for $ 2 3 5 , 0 0 0 , while direct...

Q:

S A resistivity log of a reservoir showed that two zones exist: zone 1 is completely saturated with water, zone 2 with water and oil. Use the data below to compute the oil saturation in zone 2 F Zone...

Q:

Explain the difference between Job Analysis, Job Classification, and Job Evaluation.

Q:

What does Processing of an OLAP Cube accomplish?

Q:

After designing a Multidimensional Database in Visual Studio, what are the next steps that build the Database in the Analysis Services Instance? How is the build out of the Analytical Services...