You will look at the accuracy and precision of several pieces of laboratory glassware by measuring...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
You will look at the accuracy and precision of several pieces of laboratory glassware by measuring the volumes (20 mL aliquots) with the glassware, then comparing your volume to the accurately determined mass of the samples. Separately you will determine the rate of water evaporation from a damp sample. PROCEDURE Part I. Glassware. Obtain a 100 mL beaker, two 50 mL beakers, a 50 mL graduated cylinder and a 20 mL volumetric pipette. Label the 50 mL beakers "A" and "B". Wet and briskly shake dry beaker A, then record its mass. (Fully dry the outside of the beaker with paper towels as necessary) Note that all mass measurements for Part I will be taken with Beaker A. Do not take any other glassware into the balance room. Before heading to the balance room be absolutely sure that the outside of the beaker is completely dry. Keeping the beaker on a dry paper towel will help ensure this. After each measurement, pour the contents of the beaker into the sink, and briskly shake the beaker dry. Do not towel dry the inside of the beaker. Measure 20 mL of water in your 100 mL beaker. If your beaker is one without the stamped on lines, get different beaker that does have the lines. Try to look straight through the beaker to avoid parallax. Pour the contents of the 100 mL beaker into Beaker A and weigh. Repeat this for 3 trials. Measure out 20 mL of water with Beaker A and weigh as above. Repeat this for 3 trials. There is no need to transfer the water in this step as you are using "Beaker A". But be sure to dump the water and start fresh with each trial. Repeat the above with 50 mL beaker "B". Do transfer the water to beaker "A" for weighing. Repeat the measuring process with your 50 mL graduated cylinder. Again, transfer the liquid to beaker A for weighing. Repeat the process with the 20 mL volumetric pipette. The contents of the pipette should be drained directly into beaker "A". Part II. Moisture. Weigh a 50 mL beaker and record the mass. Cut or tear a piece of paper towel approximately 4 inches square, add it to the beaker and reweigh. Add about 1 ml (20 DROPS) of water to the paper towel and squeeze it a few times to make the moisture somewhat uniformly distributed. Using a timer (watch, clock, phone), record the mass of the beaker & paper towel every 5 minutes. You don't have to be exact with the time, but try to be within 30 seconds of the 5 minute interval for each measurement. Record the masses for 25 minutes. Questions. 1. What advantage does briskly shaking the beaker dry impart? 2. Small beakers often have the volume labels incorrectly placed by 2-5 mL. Why is this not considered a problem by the manufacturer? 3. Generally, more trials lead to more reliable results. In this lab, however, more trials will almost certainly expand the range of collected values and thus the relative error. How can this be compensated for? That is, explain how more trials could be made to improve the experiment. 29 You will look at the accuracy and precision of several pieces of laboratory glassware by measuring the volumes (20 mL aliquots) with the glassware, then comparing your volume to the accurately determined mass of the samples. Separately you will determine the rate of water evaporation from a damp sample. PROCEDURE Part I. Glassware. Obtain a 100 mL beaker, two 50 mL beakers, a 50 mL graduated cylinder and a 20 mL volumetric pipette. Label the 50 mL beakers "A" and "B". Wet and briskly shake dry beaker A, then record its mass. (Fully dry the outside of the beaker with paper towels as necessary) Note that all mass measurements for Part I will be taken with Beaker A. Do not take any other glassware into the balance room. Before heading to the balance room be absolutely sure that the outside of the beaker is completely dry. Keeping the beaker on a dry paper towel will help ensure this. After each measurement, pour the contents of the beaker into the sink, and briskly shake the beaker dry. Do not towel dry the inside of the beaker. Measure 20 mL of water in your 100 mL beaker. If your beaker is one without the stamped on lines, get different beaker that does have the lines. Try to look straight through the beaker to avoid parallax. Pour the contents of the 100 mL beaker into Beaker A and weigh. Repeat this for 3 trials. Measure out 20 mL of water with Beaker A and weigh as above. Repeat this for 3 trials. There is no need to transfer the water in this step as you are using "Beaker A". But be sure to dump the water and start fresh with each trial. Repeat the above with 50 mL beaker "B". Do transfer the water to beaker "A" for weighing. Repeat the measuring process with your 50 mL graduated cylinder. Again, transfer the liquid to beaker A for weighing. Repeat the process with the 20 mL volumetric pipette. The contents of the pipette should be drained directly into beaker "A". Part II. Moisture. Weigh a 50 mL beaker and record the mass. Cut or tear a piece of paper towel approximately 4 inches square, add it to the beaker and reweigh. Add about 1 ml (20 DROPS) of water to the paper towel and squeeze it a few times to make the moisture somewhat uniformly distributed. Using a timer (watch, clock, phone), record the mass of the beaker & paper towel every 5 minutes. You don't have to be exact with the time, but try to be within 30 seconds of the 5 minute interval for each measurement. Record the masses for 25 minutes. Questions. 1. What advantage does briskly shaking the beaker dry impart? 2. Small beakers often have the volume labels incorrectly placed by 2-5 mL. Why is this not considered a problem by the manufacturer? 3. Generally, more trials lead to more reliable results. In this lab, however, more trials will almost certainly expand the range of collected values and thus the relative error. How can this be compensated for? That is, explain how more trials could be made to improve the experiment. 29
Expert Answer:
Answer rating: 100% (QA)
Advantage of Briskly Shaking the Beaker Dry Briskly shaking the beaker dry helps to remove excess wa... View the full answer
Related Book For
Chemistry The Central Science
ISBN: 978-0321696724
12th edition
Authors: Theodore Brown, Eugene LeMay, Bruce Bursten, Catherine Murphy, Patrick Woodward
Posted Date:
Students also viewed these databases questions
-
1. Black-Scholes-Merton Option Pricing: Use EXCEL to answer this question. Suppose that Lewis & Co. (LEW) stock is trading at $86.75. The annualized standard deviation of daily returns for LEW is...
-
A sample containing an alkali sulfate is dried, weighed and dissolved in dilute HCl. Barium chloride solution is added in excess to precipitate barium sulfate, and the precipitate is digested in the...
-
Case Study: Quick Fix Dental Practice Technology requirements Application must be built using Visual Studio 2019 or Visual Studio 2017, professional or enterprise. The community edition is not...
-
Provide the appropriate statute for your answer (format style - IRAC - Issue, Rule, Application and Conclusion.) what are your thought? Problem Scenario- Earnest is married to Janice. Earnest and...
-
Roswell Company has operating assets of $8,000,000. The company's operating income for the most recent accounting period was $600,000. The Lawrence Division of Roswell controls $1,600,000 of the...
-
Explain how the three events A, B, and C from a sample space S are related to each other in order for the following equation to hold true: P(A B C) = P(A) + P(B) + P(C)
-
Chocolate Inc. began 2007 with cash of \($55,000.\) During the year Chocolate Inc. earned revenue of \($600,000\) and collected \($620,000\) from customers. Expenses for the year totaled...
-
A painting operation is performed by a production worker at a labor cost of $1.40 per unit. A robot spray painting machine, costing $15,000, would reduce the labor cost to $0.20 per unit. If the...
-
The data given below relate to Material XXX used by Jose Shoes Factory, Inc. Beginning balance Purchase Order 30 Requisition 46 Requisition 49 Requisition 50 Purchase Order 96 Requisition 52 Returned...
-
For the differential manometer shown in Fig. 3.27, calculate the pressure difference between points A and B. The specific gravity of the oil is 0.85. 10 in 32 in Oil Water 9 in el
-
Lure Company included the following tems under invertory: Materials Advance for materials ordered Goods in Process Unexpired insurance on Invertory Advertising catalogs and shipping cartons Finished...
-
2. Explain importance of Turing Test. 3. Give any two real-life applications of Al in detail. 4. Write down the PEAS description for the following problems: I. Traffic light agent. II. Robotic Agent...
-
Before responding to this discussion, complete the Checklist for Attitudes About Patients and Families as Advisors here, A CHECKLIST FOR ATTITUDES ABOUT PATIENTS AND FAMILIES AS ADVISORS Use this...
-
Lukow Products is investigating the purchase of automated equipment that will save $130,000 each year in direct labor and inventory carrying costs. This equipment costs $780,000 and is expected to...
-
Forest Products, Incorporated manufactures three products (FP 10, FP 20, and FP-40) from a single, joint input. None of the products can be sold without further processing. In November, joint product...
-
Watson Hospital System recently purchased an MRI machine and incurred the following: $200,000 for purchase price of MRI machine $4,000 for delivery of the machine $1,000 to train staff on the...
-
3. Prove that for any natural number n, +3/32+ 2(n +1-1) <1+ + <2n. n
-
What steps must a business take to implement a program of social responsibility?
-
(a) What is the difference between a battery and a fuel cell? (b) Can the "fuel" of a fuel cell be a solid? Explain.
-
(a) Give the conjugate base of the following Brnsted- Lowry acids: (i) HIO3, (ii) NH4+. (b) Give the conjugate acid of the following Brnsted-Lowry bases: (i) O2-, (ii) H2PO4-.
-
(a) Compare the electronic structures of atomic chromium and atomic selenium. In what respects are they similar, and in what respects do they differ? (b) Chromium is a metal, and selenium is a...
-
The audit procedures applied to accrued liabilities differ from those applied to accounts payable because a. Accrued liabilities balances are less material than accounts payable balances. b. Evidence...
-
Match each assertion to the related audit objective. Each assertion may be used once, more than once, or not at all. Audit objective 1. To determine whether the amount shown as invento- ries in the...
-
Audit procedures should be designed to accomplish specific audit objectives. Review the following inventory audit procedures and indicate which audit objectives are being accomplished and how. a....
Study smarter with the SolutionInn App