Question: Define exergy.

Define exergy. 

Step by Step Solution

★★★★★

3.28 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Exergy also known as availability or available work is a thermodynamic property used in the field of ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Sustainable Engineering Questions!

Q:

Perform the exergy analysis of the recuperated gas turbine of Exercise 7.15 knowing that i) The exergy input of the system is 14.26 MW, ii) The chemical exergy of the flue gas is 11 kJ/kg, and iii)...

Q:

Use the exergy equation to evaluate the exergy destruction for Problem 10.44. A 2-kg piece of iron is heated from room temperature 25C to 400C by a heat source at 600C. What is the irreversibility in...

Q:

The exergy of the steam at state 1 is nearest: (A) 1340 kJ/kg (B) 17900 kJ/kg (C) 3030 kJ/kg (D) 4400 kJ/kg Steam enters a turbine (see Figures 6.39 and 6.40) at 4 MPa and 500° C and leaves as...

Q:

Define exergy and explain how it is used to measure the efficiency of a thermodynamic system.

Q:

Problem 2 : Energetic and exergetic analysis of a steam power system Consider a power cycle with one open feedwater heater. The working fluid is water. Assumptions: State 5 and state 7 are saturated...

Q:

Consider the car engine where the fuel energy of 3 3 3 kW is delivered at constant temperature of 1 5 0 0 K . The thermal efficiency of the engine is 3 0 % , thus producing 1 0 0 kW of work. The 7 0...

Q:

In the manufacture of paper, large amounts of electricity, process steam, and hot water are required. While these three needs could be met by individual thermal energy systems, it is prudent to...

Q:

Final answers for each question is: Around 12 kJ Around 6 kJ Around -1kJ use 0.018 kg for the mass of material. (a) The initial internal energy, volume, and entropy can be found at the superheated...

Q:

As shown below, two steam streams flow into a mixer and the combined stream further enters an adiabatic, steady-state turbine. The mixer operates at constant pressure and is not well insulated, with...

Q:

Final answers for each question is: Around 12 kJ Around 6 kJ Around -1kJ use 0.018 kg for the mass of material. (a) The initial internal energy, volume, and entropy can be found at the superheated...

Q:

4. Devise a synthesis for the bromohydrin shown from bromocyclohexane. Multiple steps are required, and you may use any combination of reagents and chemicals. Br Br Br

Q:

2. A university produces two commodities: research and teaching. The university uses the resources include faculty and staff, libraries, classroom, labs and so on. The following schedule indicates...

Q:

Question 2 of 4 - - of 3 points Question 2 Holding everything else constant, if a corporation begins to suffer large losses, then the default risk on its bonds will and the expected return on those...

Q:

What are the major differences between operating and capital leases?

Q:

A lawn mower engine is started by pulling a cord wrapped around a hub of radius 6.0 cm. If a constant tension of 80 N is maintained in the cord and the hub makes three revolutions before the motor...

Q:

In the movie Back to the Future, Doc Brown and the young Marty McFly need 1.21 GW of power for their time machine. (a) Convert that power requirement to horsepower. (b) If a stock DeLorean sports car...

Q:

A sprinter runs using a force of 200 N and a power output of 600 W. Calculate how many minutes it takes for the runner to run 1 km.

Q:

Problem 3-8 (Static) Balance sheet; errors; missing amounts [LO3-2, 3-3] The following incomplete balance sheet for the Sanderson Manufacturing Company was prepared by the companys controller. As...

Q:

Required information [The following information applies to the questions displayed below.] In 2019, Janet and Ray are married filing jointly. They have five dependent children under 18 years of age....

Q:

Kansas Supplies is a manufacturer of plastic parts that uses the weighted-average process costing method to account for costs of production. It produces parts in three separate departments: Molding,...