Question: Three forces are applied to a bracket as shown. The directions of the two 150-N forces may vary, but the angle between these forces is

Three forces are applied to a bracket as shown. The directions of the two 150-N forces may vary, but the angle between these forces is always 50Â°. Determine the range of values of Î± for which the magnitude of the resultant of the forces acting at A is less than 600 N.

500 N 30 150 N 50 150 N

Step by Step Solution

★★★★★

3.32 Rating (173 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Combine the two 150N forces into a resultant force Q Q 2150 N c... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

1221-P-M-K(1429).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

Three forces are applied to a bracket. The directions of the two 30-lb forces can vary, but the angle between these forces is always 50°. Determine the range of values of Î± for...

Three forces are applied to a square plate as shown in Fig. 1.53. Find the modulus, direction, and the point of application of the resultant force, if this point is taken on the side BC. -F FVZ

Three forces are applied to a tree sapling, as shown in Fig. 9-41, to stabilize it. If FA = 310 N and FB = 425 N, find FC in magnitude and direction 110 FC

If the resultant of two forces exerted on the body at A of Fig. H is to be vertical, determine the value of for which the magnitude of P is maximum, and the corresponding magnitude of P . ( Ans . = 1...

g) h) 5 KN 50 mm 20 mm 150 mm 40 mm 2 kN 200 mm 5 kN 1 kN Three forces are applied to member ABD as shown. The cross-section is a hollow rectangle with 20mm height and 40mm width and a wall thickness...

Procedure I Data Table 1: Mass and Weight Object Mass in g Mass in kg Weight in N Wooden Friction block 31.1 0.031 0.30 Glass /sandpaper friction block 55.6 0.056 0.55 50 g hanging mass 50 0.05 0.49...

Please use the information given to completely fill in tables 1-3 .... Please use the information given to completely fill in tables 1-3 . Please also draw a vector sum diagram and a component...

ORGANIZ/fIION DE\\IELOPMENT 4t XieS&r& L:rlt ttttrc DONALD R.BRO\\MN i',ii+ir+,::':i'i Organlzation Renewal: The Challenge-of Change LEARNING OBJECTIVES Upon completing this chapter, you will be able...

help me with this lab Manual Page: 30 Lab VII: Page 2 of 4 2. Select as the first problem, one of the problems with 2 given forces. Set up the two given forces on the force table and determine...

Refer to the financial statements of Williams-Sonoma, Inc., given in Appendix D at the end of this book. 1. How much interest expense did Williams-Sonoma record in 2003, 2004, and 2005? 2. What is...

The images of the imaginary axis and the line y = V3x +7 under fintersect at an acute angle equal to . What is a? You may use the fact that f (z))s holomorphic everywhere except z = -1

a super normal growth stock generally : a ) is associated with a company that is experiencing rapid contraction b ) tends to increase it's dividends per share by 3 0 % or more c ) has high growth...

Explain the two sides to this issue. Take one side or the other, and defend your position.

As a block of wood is sanded, it exerts on the disk of the sander a force F of magnitude 1.8 lb. Knowing that the belt forces exerted on the 5-in.- diameter pulley lie in a plane parallel to yz...

A car owner uses wrench ABC to loosen the lug nut at C. The length of the handle AB is 372 mm, and the owner applies forces A and B to the wrench. Knowing that these forces are equivalent to a...

While using a pencil sharpener, a student applies the forces and couple shown. (a) Determine the forces exerted at B and C knowing that these forces and the couple are equivalent to a force-couple...

solve both questions hand written and show work 3. Given the following cumulative distribution function (CDF) X4 (a) Using the above CDF, evaluate P(-1

A new start up requires JMD35,000, and has a required rate of return of 7% and the expected cash flows below, how much should a logical financial manager invest in the opportunity to make a marginal...

You are evaluating a project that requires an investment of $103 today and garantees a single cash flow of $126 one year from now. You decide to use 100% debt financing, that is, you will borrow...