Question: Two L3 3 -in. angles are welded to a C10 20 channel. Determine the moments of inertia of the combined section with

Two L3 × 3 × ¼-in. angles are welded to a C10 × 20 channel. Determine the moments of inertia of the combined section with respect to centroidal axes respectively parallel and perpendicular to the web of the channel.

L3 x3 x C10 x 20

Step by Step Solution

★★★★★

3.30 Rating (176 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

4445 ind 0842 in Y Lx x 0606in Angle Channel Locate the centroid Now X 0 4 Y A 144 in x ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

17-E-M-E-V-M-S (1100).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Propose structures for compounds that meet the following descriptions: (a) C5H8, with IR absorptions at 3300 and 2150 cm1 (b) C4H80, with a strong IR absorption at 3400 cm1 (c) C4H80, with a strong...

Two L3 Ã 3 Ã ¼-in. angles are welded to a C10 Ã 20 channel. Determine the moments of inertia of the combined section with respect to centroidal axes respectively parallel...

Determine the moments of inertia Ix and Iy of the area shown with respect to centroidal axes respectively parallel and perpendicular to side AB. 40 mm 30 mm 15 mm 24 mm 27 m

Determine the moments of inertia Ix and Iy of the area shown with respect to centroidal axes respectively parallel and perpendicular to side AB. 21 mm 21 mm 45mm 60 mm .

Two L76 76 6.4-mm angles are welded to a C250 22.8 channel. Determine the moments of inertia of the combined section with respect to centroidal axes respectively parallel and perpendicular to the...

Two L4 4 1/2 -in. angles are welded to a steel plate as shown. Determine the moments of inertia of the combined section with respect to centroidal axes respectively parallel and perpendicular to...

Two L76 Ã 76 Ã 6.4-mm angles are welded to a C250 Ã 30 channel. Determine the moments of inertia of the combined section with respect to centroidal axes respectively...

Four 3 3 -in. angles are welded to a rolled W section as shown. Determine the moments of inertia and the radii of gyration of the combined section with respect to its centroidal x and y axes. in....

Two L 4 \ times 4 \ times 1 2 Two L 4 4 1 2 - in . angles are welded to a steel plate as shown in the figure, where h = 1 6 i n . Determine the moments of inertia of the combined section with respect...

Two L 4 4 1 2 - in . angles are welded to a steel plate as shown in the figure, where h = 2 4 in . Determine the moments of inertia of the combined section with respect to centroidal axes, parallel...

Two \ ( L 4 \ times 4 \ times \ frac { 1 } { 2 } - \ mathrm { in } \ ) . angles are welded to a steel plate as shown in the figure, where \ ( h = 2 0 \ mathrm { in } \ ) . Determine the moments of...

To do: Complete the tasks requested below. For this homework, you may not use any pre-built MATLAB functions to replace calculations. You may use any trigonometric functions, as well as the length,...

a) Calculate the integral: 12 1 SS 3 dy dx 02x (1+y) b) Find the blade mass enclosed by the curves x + 3y = 0 and x - y + 4 = O with density 8(x, y) = y.

Evaluate the indefinite integral given below. - 7 x 3 c o s ( 5 x 4 1 0 ) d x

You wish to design an effusion source for Br atoms from Br2 (g). Br2 (g) 2Br (g) (a) If the source is to operate at a total pressure of 0.0132 bar at 1000 K, what is the value of the equilibrium...

What is chemistry

A light beam makes a symmetric pass through a prism (A = 5 degrees), which has a refractive index n = 1.635 for a light (wavelength = 656.3 nm). What is the angle of incidence on the first surface of...

A convex mirror has a focal length of -20 cm. What is the object distance if the image distance is -10 cm?

The actual depth of a shallow pool 1.00 m deep is not the same as the apparent depth seen when you look straight down at the pool from above. How deep (in cm) will it appear to be? (nwater = 1.33.)

should be changed? Why or why not?

The rig shown consists of a 1200-lb horizontal member ABC and a vertical member DBE welded together at B. The rig is being used to raise a 3600-lb crate at a distance x = 12 ft from the vertical...

For the rig and crate of Prob. 4.43, and assuming that cable is anchored at F as shown, determine (a) The required tension in cable ADCF if the maximum value of the couple at E as x varies from 1.5...

A 175-kg utility pole is used to support at C the end of an electric wire. The tension in the wire is 600 N, and the wire forms an angle of 15 with the horizontal at C. Determine the largest and...

Knowing that the tension in wire BD is 1300 N, determine the reaction at the fixed support C of the frame shown. 750 N 150 mm 250 mm 500 mili- 450 N 600 mm 400 mm

Determine the range of allowable values of the tension in wire BD if the magnitude of the couple at the fixed support C is not to exceed 100 N m. 750 N 150 mm 250 mm 500 mm 450 N 600 mm 400 mm

Can you please get me the descriptive answer for the below question: After taking 8 samples (each sample contains 5 parts) youwant to calculate the control limits of the X-bar and R charts.Use the...