Question: Using the same scale for stress, we note that the tensile true stress-true strain curve is higher than the engineering stress-strain curve. Explain whether this

Using the same scale for stress, we note that the tensile true stress-true strain curve is higher than the engineering stress-strain curve. Explain whether this condition also holds for a compression test.

Step by Step Solution

★★★★★

3.52 Rating (172 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

When a specimen is subjected to compression test there is an increase in the cross sectional a... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

972-E-M-E-B-D (241).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A tension test was performed on a steel specimen having an original diameter of 0.503 in. and gage length of 2.00 in. The data is listed in the table. Plot the stressstrain diagram and determine...

Let x(n) be the input signal to a discrete-time filter with impulse response hi(n) and let yi(n) be the corresponding out put. (a) Compute and sketch x(n) and yi(n) in the following cases. Using the...

The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, we may use a characteristic tensile stress (as obtained...

Load (N) 4000 3500 3000 X (fracture) 2500 2000 1500 1000 500 0 0 4 6 8 10 12 Extension (mm) Fig. 2 Load versus extension for Aluminum 6061-T6 during a tensile test 162 Chapter 6 / Mechanical...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Objectives 1 ) Conduct the tensile test and obtain the force - elongation data and diagram for the tested materials. 2 ) Plot the stress - strain diagrams for the tested materials. 3 ) Measure the...

The following data were collected from a test specimen of cold-rolled and annealed brass. The specimen had an initial gage length l0 of 35 mm and an initial cross sectional area A0 of 10.5 mm2? (a)...

A bar with a rectangular cross section that has a width of 2 4 . 5 mm , a thickness of 6 . 1 mm and a gauge length of 7 5 mm was tested in tension to fracture. Use the load - elongation...

3. a. Draw the stress-strain curves for the following materials/items. (We recommend trying to put them all on the same plot for perspective, but make sure you have plenty of space.) Label the...

A tensile test is conducted on a rectangular cross - section steel alloy bar with dimensions 6 . 2 5 mm x 3 7 . 5 mm and a initial length of 2 0 3 mm . The results obtained from the experiment are...

Angelas Company issued a $500,000, 10 percent, 10-year bond on January 1, 2015, for 113.6 when the effective interest rate was 8 percent. Interest is payable on June 30 and December 31. Using the...

The Treasury Manager of G.E. receives word that a payment in the amount of 50,000,000 to Hitachi will be due in June 2020, Hitachi requires the payment to be made in Japanese Yen (). The Treasury...

You have taken out a loan of $ 1 3 , 0 0 0 for 4 years with an interest rate of 6 % compounded annually. The loan will be repaid by end of year payments. Fill in all the boxes below, and round all...

Is the behaviour of the volume of exports a satisfactory measure of a country's competitiveness?

Generalize Prob. 362 for a solid shaft of diameter d replaced with a hollow shaft of the same material with an outside diameter d, and an inside diameter that is a fraction of the outside diameter, x...

A hollow steel shaft is to transmit 4200 N m of torque and is to be sized so that the torsional stress does not exceed 120 MPa. (a) If the inside diameter is 70 percent of the outside diameter, what...

The figure shows an endless-belt conveyor drive roll. The roll has a diameter 120 mm and is driven at 10 rev/min by a geared-motor source rated at 1.5 kW. Determine a suitable shaft diameter dC for...

The engineering team at Manuels Manufacturing, Inc., is planning to purchase an enterprise resource planning (ERP) system. The software and installation from Vendor A costs $405,000 initially and is...

Thanks for the help in advance! Problem 11-18 Using the SML [LO 4] Asset W has an expected return of 13.75 percent and a beta of 1.4. If the risk-free rate is 4.65 percent, complete the following...

Apps Manga ] Work ) School Charms The fastest free Y... convert anything t... Naruto Universe... DL with TubeOffline Read Are You Alic.. Question o 4 pts Credit Fall 2021 Home Suppose 4 quarters, 2...