Question: What is the maximum possible value of the clamping force C in the jaws of the pliers shown in the figure if the ultimate shear

What is the maximum possible value of the clamping force C in the jaws of the pliers shown in the figure if the ultimate shear stress in the 5-mm diameter pin is 340 MPa?
What is the maximum permissible value of the applied load P if a factor of safety of 3.0 with respect to failure of the pin is to be maintained?

10 y 15 mm 90 90 50% RT x 140 125 mm Pin 50 mm

Step by Step Solution

★★★★★

3.26 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

NUMERICAL DATA R x C cos R y P C sin a ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (74).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

What is the maximum possible value of the angular momentum for an outer electron in the ground state of a bromine atom?

In Fig P3.174 the piston drives water at 20°C. Neglecting losses, estimate the exit velocity V2 ft/s. If D2 is further constricted, what is the maximum possible value of V2? D2-4 in Water 1)

A rocket of mass M moves along an x axis at the constant speed vi = 40m/s. A small explosion separates the rocket into a rear section (of mass m1) and a front section; both sections move along the x...

Problem 1 . 9 - 1 2 Pts : 1 0 ( a ) What is the maximum possible value of the clamping force C in the jaws of the pliers shown in the figure, if the ultimate shear stress in the 5 - m m diameter pin...

1 . 7 - 9 What is the maximum possible value of the clamping force C in the jaws of the pliers shown in the figure if a = 3 . 7 5 in . , b = 1 . 6 0 i n . , and the ultimate shear stress in the 0 . 2...

What is the maximum possible value of the clamping force C in the jaws of the pliers shown in the figure if the ultimate shear stress in the 6 - mm diameter pin is 3 0 0 MPa? What is the maximum...

Problem 1 : The following data supply to the clamp shown in the figure: Acme thread Single threading with N = 1 4 thread / in Outside diameter of 1 2 in = 0 . 5 in = d o Root diameter of 0 . 4 3 5 0...

Consider the design of the pliers wrench presented and drawn according to the scale shown in Figure 1 ( each grid measures 0 . 5 cm on each side ) . Answer the following questions. ( a ) Draw the...

Need summary for this . Make sure someone who understands it and summarize it in 2 pages with some summary of the data also Article history: The interactions of a 1/2{111} edge dislocation with a...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Calculate Average, STD, C.V. (%), error, %error. Table A. Mass Mass 1 Mass 2 Mass 3 Mass 4 Mass 5 Report of balance calibration results. Balance #1 (g) Reference weight 1 1 grams 1,0003 1.0000 0.9999...

On January 1, 2018, sunder statesrn began construction of a new warehouse. The building was finished and ready for use on September 30, 2019. Expenditures on the project were as follows: January 1,...

Rank the potentially dilutive securities from most dilutive to least dilutive. Options $ 3 . 6 0 Preferred shares 5 % bonds 8 % bonds

1. A is a single value computed from sample information used to estimate a population parameter.

The motor delivers 50 hp while turning at a constant rate of 1350 rpm at A. Using the belt and pulley system this loading is delivered to the steel blower shaft BC. Determine to the nearest 1/8 in....

The shaft is subjected to a distributed torque along its length of t = (10x 2 ) N m/m, where x is in meters. If the maximum stress in the shaft is to remain constant at 80 MPa, determine the required...

Please provide formula Add-in Problem Sorry, we couldn't find Solver.xlam. Is it possible it was moved, renamed or deleted? A6 fc Net Income E F G H K Balance sheet 27,000 Debt Equity Total 20,000...

Shawna Carter wants to invest her recent bonus in a five-year bond that pays a coupon of 11 percent semiannually. The bonds are selling at $962.13 today. If she buys this bond and holds it to...

Give Details Identify the order of q for each of following MA model models and determine whether they are invertible: a xt=wt0.3wt1+0.1wt2 b xt=wtwt1