When cycle counting inventory, why do experts recommend a lower acceptable error tolerance for A items than

Question:

When cycle counting inventory, why do experts recommend a lower acceptable error tolerance for A items than B or C items?

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For answer-question

Operations and Supply Chain Management The Core

ISBN: 978-1259696596

4th edition

Authors: F. Robert Jacobs, Richard Chase

See More Books

Question Posted: Oct 21, 2016 03:37 AM

See More Questions

1. What are the primary reasons why many employees are experiencing high levels of stress at work nowadays? Identify and describe these reasons. 2. Why do many of the survivors of layoffs experience...
Mr. and Mrs. Gresko started Gresko Toys in the early 1 960s. Initially, the company was small and few toys were produced. The talent and skills of Mr. Gresko were by far the major assets of the...
For each of the following brief scenarios, assume that you are reporting on a clients financial statements. Reply as to the type(s) of opinion (per below) possible for the scenario. In addition: ...
Another liability that employers have is that of unemployment insurance. Class, let's talk about this a little more. At what levels are unemployment liabilities incurred? What are some additional...
What is the general formula used to calculate the price of a share of a stock? What does it mean?
A not-for-profit organization receives a restricted gift. When, and in which type of fund, should it recognize the revenue? When, and in which type of fund, should it recognize the related expense?...
You need to understand the approach described in question 3 in More Genetic TIPS before answering this question. A gene that is normally expressed in pancreatic cells was cloned and then subjected to...
Physical Phitness, Inc. operates three divisions, Weak, Average, and Strong. As it turns out, the Weak division has the lowest operating income, and the president wants to close it. "Survival of the...
Identify and analyze at least two considerations to ensure effective transaction transparency of Centralized database management systems and Distributed Database management systems. Identify...
KeyCite this case: United States v. Martinez-Jimenez, 864 F.2d 664 (9th Cir. 1989), what are the citations of the 1995 and 1993 cases listed under Positive History that have a yellow flag? For...
The cost of performing inspection sampling moves inversely to the cost of quality failures. We can reduce the cost of quality failures by increased levels of inspection, but that of course would...
"The nice thing about inventory models is that you can pull one off the shelf and apply it so long as your cost estimates are accurate." Comment.
Use a tax service to give three parallel citations for Falstone, Inc. v. Commissioner, a Ninth Circuit Court of Appeals case decided in 2003. Using only the headnote(s), determine the issue(s) in...
2. c) 6.0 Evaluate these integrals: a) 6; S 11 dx S x+1' 5x+11 x+2x-3 d) dx; 2xdx x +1' h) nx dx; b) 3 dx e) 1 (2441 x+1' S ln x dx. e x lnx dx; f) x-2x- dx; (x-1)
Find the derivative. F'(x) if F(x) = (ex +3) 8 F'(x)= Question Viewer
1. Given u = [1, 0, -1], y = [-4, -3, -2] and w = [1, 1, -2], find (i) + 2 w (ii) U V +. - the angle between vectors (2u - y) and (w - v ) (iii) a vector which is perpendicular to both W and V (iv)...
3. Let the function f be defined as follows f(x) = a) Show f is continuous at x =1. (1 mark) [x, x>1 3x-2,x1
The amount of radioactive material decreases at a rate proportional to the amount present. Write a differential equation to model the situation: Differential equation: A'(t)/t+kA Find a formula for...
For the circuit shown, a power of 100. watts is dissipated in the resistor. Find the resistance, R. The circuit for this exercise is given in the table. | = 15 A 100. 2 100. 12V Exercise 1 Exercise...
A 20-cm-square vertical plate is heated to a temperature of 30oC and submerged in glycerin at 10oC. Calculate the heat lost from both sides of the plate.
Match the following product types to the appropriate product development description. _______Technology-push products _______Platform products _______Process-intensive products _______High-risk...
Designing products for aesthetics and with the user in mind is generally called what?
What is it about service processes that makes their design and operation so different from manufacturing processes?
I appreciate your perspective on the key components of materials management. I concur that Materials Management in healthcare is one of the critical departments, and its main objective is to...
Consider why a hospital is different than a nuclear power plan or a commercial airplane as it relates to achieving the same quality levels as high-reliability organizations. Then, reflect on the...
Miranda Manufacturing is managing for its stakeholders. Because of this, it is likely to: perform poorly on CSR. perform poorly on ESG. enjoy above-average returns compared to firms that do not...

When cycle counting inventory, why do experts recommend a lower acceptable error tolerance for A items than

Question:

Step by Step Answer:

A items are more valuable so quantity variations ar...View the full answer

Operations and Supply Chain Management The Core

Students also viewed these Management Leadership questions