Question: Why is it desirable to design a casting to have directional solidification sweeping from the extremities of the mold to the riser?

Why is it desirable to design a casting to have directional solidification sweeping from the extremities of the mold to the riser?

Step by Step Solution

★★★★★

3.39 Rating (165 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Hence for final analysis we can say that by havi... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Document Format (1 attachment)

Word file Icon

916-E-M-S-E-M-S (1242).docx

120 KBs Word File

Students Have Also Explored These Related Materials Science Engineering Questions!

Q:

A gas stream containing 40.0mole% hydrogen, 35.0% carbon monoxide, 20.0% carbon dioxide, and 5.0% methane is cooled from 1000C to 10C at a constant absolute pressure of 35.0 atm. Gas enters the...

Q:

Why is it desirable to make the pattern allowances as small as possible?

Q:

When designing a decorative surface (design or lettering) on a plastic product, why is it desirable that the details be raised on the product rather than depressed?

Q:

A part is to be cast (the Casting in the figure). The volume of this part is 300,0000 mm and the surface area is 160,000 mm. Assume the mold constant C is 1 and exponent n is 2. We are considering...

Q:

Problem 1 : Design a Casting Mold An aluminum workpiece shown below is to be manufactured by sand casting ( can assume part to be a box ) . Casting is done by pouring the liquid metal into the...

Q:

Project 1: In the first project, you have been asked to work on some design problems and technically support the team working on casting department: The team are casting a rectangular plate as shown...

Q:

Dave Q - 1 4 Strian in a given materal is the ratio of a ) Change in dimension to original dimension b ) Applied load to original dimention. c ) change in dimension to the area of cross section or...

Q:

A cylindrical steel casting has a diameter of 4 , a height of 8 , and requires a riser to ensure no shrinkage occurs during solidification. The casting solidifies in 1 5 minutes. ( a ) Determine the...

Q:

Solve for f only Only (f) Project 1: Q1) Given the following part (Isometric, Front and section A-A Views in the following figure): a) Calculates casting volume ? b) Calculates the casting surface...

Q:

Answers for all from a to f please Project 1 : Q1) Given the following part (Isometric, Front and section A-A Views in the following figure): a) Calculates casting volume ? b) Calculates the casting...

Q:

Catchment Descriptors for Mill Creek Descriptor Units AREA L S1085 URBAN RSMD (ha) (km) (m/km) (%) (mm) Value 900 26 51 5 5 2.5 Mill Creek sub-catchment SUH derived hydrograph response to design...

Q:

Explain what each of the three numbered hazard ratings means for 37 wt% HCl in Figure 2-2.

Q:

CHALLENGE Assessment of a foreign-language institute. The National Endowment for the Humanities sponsors summer institutes to improve the skills of high school teachers of foreign languages. One such...

Q:

Suppose that a freely determined price of kerosene oil is Rs 4.00 per litre. The government fixes its controlled price at Rs 3.00 per litre. At this price there is a shortfall of 20 lakh litres...

Q:

Poissons ratio is a material property and is the ratio of the lateral strain and the longitudinal strain for a member in tension. For a homogeneous, isotropic material, the modulus of rigidity G is...

Q:

A specimen of medium-carbon steel having an initial diameter of 0.503 in was tested in tension using a gauge length of 2 in. The following data were obtained for the elastic and plastic states: Note...

Q:

Compute the true stress and the logarithmic strain using the data of Prob. 29 and plot the results on log-log paper. Then find the plastic strength coefficient 0 and the strain-strengthening exponent...

Q:

A stock has a required return of 12%, the risk-free rate is 3%, and the market risk premium is 3%. a. What is the stock's beta? Round your answer to two decimal places. two decimal places. I. If the...

Q:

Aquilera, Inc., has sales of $ 1 8 . 8 million, total assets of $ 1 3 . 8 million, and total debt of $ 4 . 6 million. The profit margin is 1 1 percent. What is the company's net income? ( Enter your...

Q:

A share of DivCorp common stock does not pay a regular dividend, but sometimes awards a special dividend of $10 per share at the end of each year. A risk-averse investor, Najar, has a subjective...