Question: Write the complete APT part program to perform the profile milling operation for the part drawing in Figure P7.29. Tooling = 20 mm diameter end

Write the complete APT part program to perform the profile milling operation for the part drawing in Figure P7.29. Tooling = 20 mm diameter end mill with two teeth, cutting speed = 125 mm/min, and feed = 0.10 mm/tooth. The part is 10 mm thick. Use the lower left corner of the part as the origin in the x-y axis system. The two holes in the part have already been drilled and will be used for clamping the part during milling. Postprocessor call statement is MACHIN/MILL, 01.

Step by Step Solution

★★★★★

3.40 Rating (162 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Spindle speed N 12520 p x 10 3 1989 revmin Feed rate f r 19892010 398 mmmin PARTNO PAR... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (485).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

Write the complete APT part program to perform the drilling operations for the part drawing in Figure P7.26. Cutting speed = 0.4 m/s, feed = 0.10 mm/rev., and table travel speed between holes = 500...

Write the complete APT part program to profile mill the outside edges of the part. The part is 15 mm thick. Tooling = 30 mm diameter end mill with four teeth, cutting speed = 150 mm/min, and feed =...

Write the APT part program to perform the drilling operations for the part. Use the TURRET command to call the different drills required. Cutting speed = 0.4 m/s, feed = 0.10 mm/rev., and table...

Write the complete APT part program to perform the profile milling operation for the partQ 1 3 . Write the complete APT part program to perform the profile milling operation for the part drawing in...

The part is to be milled, using a 20 mm diameter end mill with four teeth. Write the APT geometry and motion statements for this job. Assume that preliminary passes have been completed so that only...

The outline of the part in the previous problem is to be profile milled using a 30 mm diameter end mill with four teeth. The part is 15 mm thick. Cutting speed = 150 mm/min and feed = 0.085 mm/tooth....

Assignment Brief The S.W.E.A.T Lab is currently upgrading the conveyor line to meet Industry 4.0 standards where a central PLC with a MES system governing majority of the tasks. One of the tasks is...

The outline of the part in Figure P7.29 is to be profile milled, using a 20 mm diameter end mill with two teeth. The part is 10 mm thick. Cutting speed = 125 mm/min and feed = 0.10 mm/tooth. Use the...

The outline of the cam in Figure P7.38 is to be machined in an end milling operation, using a 12.5 mm diameter end mill with two teeth. The part is 7.5 mm thick. Write the complete APT program for...

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

January 1, 2019, We Establish Arab Capital Insurance Inc. With Capital $955,955 Cash And We Purchase Apple And David Inc. They Use Acquisition Methods. We Paid $655,000 Cash For Apple Inc. Also,...

Given two assets with the following characteristics: E(R1) = 0:12 1 = 0:04 E(R2) = 0:16 2 = 0:06 Assume that r1,2 = 1.00. What is the weight that would yield a zero variance for the portfolio?

The productive efficiency of the Brighton Company depends upon superiorgroup leaders and foremen. The company management suggests that groupleaders, foremen, and selected workmen organize a class in...

Respond Why do you think retail stores stamp checks for deposit only when they are received?

Consider building a CSMA/CD network running at 1 Gbps over a 1-km cable with no repeaters. The signal speed in the cable is 200,000 km/sec. What is the minimum frame size?

An IP packet to be transmitted by Ethernet is 60 bytes long, including all its headers. If LLC is not in use, is padding needed in the Ethernet frame, and if so, how many bytes?

Ethernet frames must be at least 64 bytes long to ensure that the transmitter is still going in the event of a collision at the far end of the cable. Fast Ethernet has the same 64-byte minimum frame...

It says "Mark owns a 20% interest in a partnership (not real estate) in which his at-risk amount is $44000 at the beginning of the year. During the year, the partnership borrows $90000 on a recoursw...

QUESTIONS Vrterest id or accrued during 2018 on regate quistion deteness of million or enim formare persone con is deductible wrate de interest QUESTIONS

Lupo Corporation uses a job-order costing system with a single plantwide predetermined overhead rate based on machine-hours. The company based its predetermined overhead rate for the current year on...