Question: A pump impeller has an outside radius of 50 cm, an inside radius of 15 cm, and vanes with a uniform opening (width) of 20

A pump impeller has an outside radius of 50 cm, an inside radius of 15 cm, and vanes with a uniform opening (width) of 20 cm. When the impeller is rotated at an angular speed of 450 rpm, water exits from the impeller with an absolute velocity of 45 m/ sec. The angle of the exiting water is 55 degrees measured from a radial line emanating from the center of the impeller outward. Determine the torque generated by the exiting flow.

Step by Step Solution

★★★★★

3.51 Rating (174 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The torque on the exiting flow is T Qr o Vocos o Where Q Aro an... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

884-P-M-F-M (822).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

Consider a cogeneration power plant that is modified with reheat and that produces 3 MW of power and supplies 7 MW of process heat. Steam enters the high-pressure turbine at 8 MPa and 500°C and...

Ring C has an inside radius of 55 mm and an outside radius of 60 mm and is positioned between two wheels A and B, each of 24-mm outside radius. Knowing that wheel A rotates with a constant angular...

Figure CS-43 is a water pump impeller used by a major automotive parts manufacturer. The outer diameter of the component is 2.75 inches and the height is specified at 0.75 ± 0.005 inches. The...

A centrifugal pump is being tested in a laboratory. The inside and outside radii of the impellers are 7 .5 cm and 15.0 cm, respectively. The width of the impeller vanes (or flow opening height)...

Consider a centrifugal blower that has a radius of 2 0 cm and a blade width of 8 . 2 cm at the impeller inlet, and a radius of 4 5 cm and a blade width of 5 . 6 cm at the outlet. The blower delivers...

Reconsider Prob. 662. For the specified flow rate, investigate the effect of discharge angle 2 on the minimum power input requirements. Assume the air to enter the impeller in the radial direction (...

Consider a centrifugal blower that has a radius of 20 cm and a blade width of 8.2 cm at the impeller inlet, and a radius of 45 cm and a blade width of 5.6 cm at the outlet. The blower delivers air at...

Solve the following Q.1 The eye of a centrifugal compressor has a hub-tip radius ratio of 0.4, a maximum relative flow Mach number of 0.9, and an absolute flow that is uniform and completely axial....

x=50 PART A 140 points| The feed water system shown in the figure below is for a pressure tank. The feed water pump is to deliver 20 m/h of water to the pressure tank. The pressure inside the feed...

almost ~ 11 th, widt he obje hey acti all are mall 3. An open topped wooden box needs to be painted on the inside and outside. The ne a outside dimensions are : length = 130 cm , width = 65 cm , and...

CHARGE TO MASS RATIO FOR THE ELECTRON OBJECTIVE: To measure the ratio of the charge of an electron to its mass. METHOD: A stream of electrons is accelerated by having them "fall" through a measured...

Which Bacteria and Archaea play a major role in acid mine drainage? Why do they carry out the reactions that they do? Why is air necessary for this process?

A uniform solid cylinder rolls without slipping down an incline. A hole is drilled through the cylinder along its axis. The radius of the hole is 0.50 times the (outer) radius of the cylinder. (a)...

Find f @ g @ h . f ( x ) = 1 x , g ( x ) = x 3 , h ( x ) = x + 6

How does Snowdens identity as an employee conflict with his identity as a citizen? Which may be the relevant values in conflict here?

What is the purpose of load-pacing gear? Describe one form of load-pacing gear and explain its principle of operation.

Matchpoint is considering producing a low-pressure ball, suited for high altitudes, called the special duty. Each gross of special duty balls would require 1 and man-hours of manufacturing and...

What effect does height have on weight for a sample of 8 children? X (Height in Y (Weight x2 XY in pounds) inches) 99 60 48 80 55 79 55 84 51 90 52 82 49 79 50 70 n

As a tax practitioner, you often get people asking questions concerning the tax effect of property transactions. This year is no exception. You've had individual clients ask you the following...

6. Suppose a population consisted of 10 items and we wished to list all possible samples of size 3. How many samples are there?

During an adiabatic process, the temperature of 3.22 moles of a monatomic ideal gas drops from 475 C to 215 C. For this gas, find (a) The work it does, (b) The heat it exchanges with its...

An ideal gas follows the three-part process shown in FIGURE 18-29. At the completion of one full cycle, find (a) The net work done by the system, (b) The net change in internal energy of the system,...

With the pressure held constant at 260 kPa, 43 mol of a monatomic ideal gas expands from an initial volume of 0.75 m3 to a final volume of 1.9 m3. (a) How much work was done by the gas during the...

A pension fund manager is considering three mutual funds. The first is a stock fund, the second is a long-term government and corporate bond fund, and the third is a T-bill money market fund that...

You purchased 100 shares of common stock on margin for $50 per share. The initial margin is 50%, and the stock pays no dividend. What would your rate of return be if you sell the stock at $59 per...

Which one of the following statements is TRUE? a. Inside directors are more concerned with shareholders' interests since they are more closely concerned with firm operations. b. Since outside...