An elbow for the duct of a ventilating system is made of sheet metal of uniform thickness.
Question:
An elbow for the duct of a ventilating system is made of sheet metal of uniform thickness. Locate the center of gravity of the elbow.
6 mm r 200 mm r 400 mm 100mm
Step by Step Answer:
First assume that the sheet metal is homogeneous so that the center of gravity of the duct coincid...View the full answer
Vector Mechanics for Engineers Statics and Dynamics
ISBN: 978-0073398242
11th edition
Authors: Ferdinand Beer, E. Russell Johnston Jr., David Mazurek, Phillip Cornwell, Brian Self
Related Video
Take 2 forks and place them on one another in such a way that we can place the coin in between the prongs. Now try to place the coin with forks on the edge of the glass. It will take you some time to adjust the coin on the edge. This requires a little practice to adjust the coin on the edge of the glass. With a little effort, we will see the coin sitting on the edge calmly. If you look closely you will see it wobbling a little bit. The mass is in the handles of the forks so as a low center of mass it stables as it looks.
Students also viewed these Mechanics questions
-
A chute is made of sheet metal of uniform thickness. Locate the center of gravity of the chute. s in 5.4 in. 36 in. 30 in.
-
Sheet metal of uniform thickness is used to fabricate a portion of the flashing for a roof. Locate the center of gravity of the flashing knowing that it is composed of the three elements shown. 240...
-
Locate the center of gravity of the sheet metal form shown. 3 in Sin r225
-
iHerb Inc. has several herb extractor evaporators that were purchased four years ago at a price of $20,000. These machines currently require annual maintenance costs of $2,000. However, the...
-
Tasha Orin is unable to reconcile the bank balance at January 31. Tashas reconciliation is shown here. Cash balance per bank ....... $3,677.20 Add: NSF check ......... 450.00 Less: Bank service...
-
When a parent decreases its investment in a subsidiary from 76 to 60%, should the non-controlling interest be remeasured at fair value? Explain.
-
This exercise considers nursing home data provided by theWisconsin Department of Health and Family Services (DHFS).The State of Wisconsin Medicaid program funds nursing home care for individuals...
-
Using the following figure, perform resource leveling. Assume that each task can be performed independently of the othertasks. Task 1 (2 workers) Task 2 (1 worker) Task 3 (3 workers) I Task 4 (2...
-
What is the purpose of the Management, Dynamic and Virtual Interfaces of WLC2504? What is PoE? How many PoE ports does the controller WLC2504 have? How many APs does wireless controller type Cisco...
-
Selected transactions for Sophies Dog Care are as follows during the month of March. March 1 Paid monthly rent of $1,200. 3 Performed services for $160 on account. 5 Performed services for cash of...
-
Locate the centroid of the plane area shown. Vertex Para 60 mm 60 mm TS mm
-
A mounting bracket for electronic components is formed from sheet metal of uniform thickness. Locate the center of gravity of the bracket. r-0.625 in. l in. 2.5 in 3 in: 0.75 in. 6 in. 1.25 in 0.75 in
-
Determine if a datagram with the following information is a first fragment, a middle fragment, a last fragment, or the only fragment (no fragmentation): a. M bit is set to 1 and the value of the...
-
Write short notes on: (a) Sin-bar, (b) Slip Gauge, (c) Combination set.
-
Explain the various techniques to perform a taper turning on a lathe.
-
Identify the common requirements for a valid common law marriage.
-
Describe the position of the federal government with respect to same-sex marriage and identify the form in which it is expressed.
-
What are the differences between shaper and planer?
-
The paper referenced in the previous exercise also compared the reported heights and weights to actual measured heights and weights for a sample of 1052 female college students selected from eight...
-
Two mutually exclusive investment alternatives are being considered. Alternative A requires an initial investment of $20,000 in a machine. Annual operating and maintenance costs are anticipated to be...
-
Using the parallel-axis theorem, determine the product of inertia of the area shown with respect to the centroidal x and y axes. 6 in. 9 in. 9 in- 4.5 in. in. 4.5 in.
-
Using the parallel-axis theorem, determine the product of inertia of the area shown with respect to the centroidal x and y axes. 120 mm 120 mm
-
Using the parallel-axis theorem, determine the product of inertia of the area shown with respect to the centroidal x and y axes. 25.1 mm 6.4 mm 12.6 mm 51 mm L76 x 51 x 6.4 6.4 ms 76 mm
-
What theorists are most likely to argue the city's form and growth come from decisions made by people and organizations that control wealth and other key resources?
-
Explain the difference between glucogenic and ketogenic amino acids
-
Describe what is an arrangement where workers who don't join a union must make payments equal to union dues and fees to get union representation services?
Study smarter with the SolutionInn App