Question: Beam AB, with elastic support kR at A and pin support at B, of length L and height h (see figure) is heated in such

Beam AB, with elastic support kR at A and pin support at B, of length L and height h (see figure) is heated in such a manner that the temperature difference T2 - T1 between the bottom and top of the beam is proportional to the distance from support A; that is, assume the temperature difference varies linearly along the beam:
T2 - T1 = T0x

in which T0 is a constant having units of temperature (degrees) per unit distance. Assume the spring at A is unaffected by the temperature change.
(a) Determine the maximum deflection Î´max of the beam.
(b) Repeat for quadratic temperature variation along the beam, T2 - T1 = T0 x2.
(c) What is Î´max for (a) and (b) above if kR goes to infinity?

T1 - T2 kR

Step by Step Solution

★★★★★

3.43 Rating (169 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a MAXIMUM DEFLECTION Set nx 0 and solve for x b MAXI... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (801).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

The beam shown below has a sliding support at A and an elastic support with spring constant k at B. A distributed load q(x) is applied over the entire beam. Find all support reactions, then plot...

Beam ABC is fixed at support A and rests (at point B) upon the midpoint of beam DE (see the first part of the figure). Thus, beam ABC may be represented as a propped cantilever beam with an overhang...

A cantilever beam AB of length L and height h (see figure) is subjected to a temperature change such that the temperature at the top is T1 and at the bottom is T2. Determine the equation of the...

A bar AB of length L is held between rigid supports and heated nonuniformly in such a manner that the temperature increase ÎT at distance x from end A is given by the expression ÎT =...

L> | Question 1 10 pts Assume the continuous beam you have chosen in Task 1 is designed to support a partial uniformly distributed load of 0.6W kN/m, a tri-angular load of 1.3*W kN/m and a Point Load...

Hello I'm trying to write a report after collecting this data about conservation of energy and momentum. Please any help would be much appreciated Data Sheet for Experiment M-9 4. Plug the small plug...

Republic of Iraq Ministry of Higher Education and Scientific Research University of Technology Chemical Engineering Department MODELING AND SIMULATION OF FCC RISERS A RESEARCH SUBMITTED TO THE...

As shown in ( a ) of the Figure, a horizontal beam AB is PIN - supported at end A and carries a load Q at joint B . The beam is also supported at C by a pinned - end column of length L . The column...

A tapered cantilever beam AB of length L has square cross sections and supports a concentrated load P at the free end [see figure part (a)]. The width and height of the beam vary linearly from hA at...

Problem 5 Problem 1 0 . 3 - 4 A cantilever beam \ ( A B \ ) of length \ ( L \ ) has a fixed support at \ ( A \ ) and a spring support at \ ( B \ ) ( see figure ) . The spring behaves in a linearly...

Your client currently has accumulated capital of $560,000 and hopes to retire this year. She wants to receive an annuity payment at the beginning of each year for the next 20 years. If the capital...

Each of the following items must be considered in preparing a statement of cash flows (indirect method) for Turbulent Indigo Inc. for the year ended December 31, 2014. a) Plant assets that had cost...

Exercise 4.27 This exercise examines how exception handling interacts with branch and load/store instructions. Problems in this exercise refer to the following branch instruction and the...

37. The level of measurement presumes that one classification is ranked higher than another.

The W14 $\times 38$ column is made of A-36 steel. Determine the critical load if its bottom end is fixed supported and its top is free to move in plane about the strong axis and is pinned about the...

The W14 $\times 38$ column is made of A-36 steel and is fixed supported at its base. If it is subjected to an axial load of $P=15$ kip, determine the factor of safety with respect to buckling. P...

The $\mathrm{W} 10 \times 45$ is made of A- 36 steel and is used as a column that has a length of $15 \mathrm{ft}$. If the ends of the column are fixed supported, can the column support the...

AMT, Inc., is considering the purchase of a digital camera for maintenance of design specifications by feeding digital pictures directly into an engineering workstation where computer-aided design...

You have $ 2 8 8 , 9 8 1 to invest in a stock portfolio ( this amount is your original wealth ) . Your choices are Stock H , with an expected return of 1 5 . 1 percent, and Stock L , with an expected...

Suppose that JPMorgan Chase sells call options on $1.10 million worth of a stock portfolio with beta = 1.45. The option delta is .52. It wishes to hedge out its resultant exposure to a market advance...