Question: Consider a Carnot refrigeration cycle executed in a closed system in the saturated liquid-vapor mixture region using 0.96 kg of refrigerant-134a as the working fluid.

Consider a Carnot refrigeration cycle executed in a closed system in the saturated liquid-vapor mixture region using 0.96 kg of refrigerant-134a as the working fluid. It is known that the maximum absolute temperature in the cycle is 1.2 times the minimum absolute temperature, and the net work input to the cycle is 22 kJ. If the refrigerant changes from saturated vapor to saturated liquid during the heat rejection process, determine the minimum pressure in the cycle.

Step by Step Solution

★★★★★

3.45 Rating (161 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

A Carnot refrigeration cycle is executed in a closed system with a fixed mass of R... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

837-P-T-S-L (640).docx

120 KBs Word File

Students Have Also Explored These Related Thermodynamics Questions!

Consider a Carnot heat-engine cycle executed in a closed system using 0.025 kg of steam as the working fluid. It is known that the maximum absolute temperature in the cycle is twice the minimum...

Consider a Carnot cycle executed in a closed system with 0.5 kg of air. The temperature limits are 50oC and 750oC, and the pressure limits are 15 kPa and 1700 kPa. Heat addition takes place from a...

Consider a Carnot cycle executed in a closed system with 0.6 kg of air. The temperature limits of the cycle are 300 and 1100 K, and the minimum and maximum pressures that occur during the cycle are...

please help!! third time posting cause no one has answered. i understand everything until i get to identifying the saturation temperature corresponding to hfg and identifying the temperature and...

please help! i need to study this problem for a final. Ive looked at other solutions and they just dont make sense. i need each step broken down and explained along with the calculations, formulas,...

Consider a Carnot refrigeration cycle executed in a closed system in the saturated liquidvapor mixture region using 0.96 kg of refrigerant-134a as the working fluid. It is known that the maximum...

Problem 0 6 . 1 3 4 - Minimum cycle pressure Consider a Carnot refrigeration cycle executed in a closed system in the saturated liquid - vapor mixture region using 0 . 9 6 0 kg of refrigerant - 1 3 4...

Consider a Carnot refrigeration cycle executed in a closed system in the saturated liquidvapor mixture region using 0.8 kg of refrigerant-134a as the working fluid. The maximum and the minimum...

Consider a Carnot vapor cycle executed in a closed system in the saturated liquidvapor mixture region using water as the working fluid.it is known that the max absolute temperature in the cycle is 1...

Discuss 3 key Operations Failings in Lidl's 500 Million SAP Debacle and how these failings can be effectively mitigated or reduced in similar operations and capital projects Please provide reference

Suppose you have the following information: Demand rate (D) = 750 units per hour Lead time (T) = 40 hours Container capacity (C) = 1,000 units Safety factor (x) = 10% How many kanban production cards...

\ table [ [ , premo: ] ] \ table [ [ , puoq uodnoo seak ] , [ Kyu ew Ploti, ] ] \ table [ [ - , Ojez Jeer ] , [ K umeW Pla!, ] ] Consider the following zero - coupon bonds and their yields: \ table [...

In trying to meet customer expectations, what are the major barriers faced by any organisation?

The shaft shown in the figure carries a 20-lbf gear on the left and a 35-lbf gear on the right. Estimate the first critical speed due to the loads, the shafts critical speed without the loads, and...

A transverse drilled and reamed hole can be used in a solid shaft to hold a pin that locates and holds a mechanical element, such as the hub of a gear, in axial position, and allows for the...

A guide pin is required to align the assembly of a two-part fixture. The nominal size of the pin is 15 mm. Make the dimensional decisions for a 15-mm basic size locational clearance fit.

LESLI CORPORATION Balance Sheet Income Statement Assets: Sales (all credit) $5,800,000 Cash $150,000 Cost of goods sold -3,000,000 Accounts receivable 450,000 Operating expense -900,000 Inventory...

Garage, Inc., has identified the following two mutually exclusive projects: Year Cash Flow (A) Cash Flow (B) 0 -28,100 -28,100 1 13,500 3,850 2 11,400 9,350 3 8,750 14,300 4 4,650 15,900 Project A...

If the simple CAPM is valid, is the situation shown below possible? Possible Not possible If the simple CAPM is valid, is the situation shown below possible? Possible Not possible If the simple CAPM...