Question: Determine the maximum deflection and maximum principal stress for the plate shown in Figure P12-9. The plate is fixed along all three sides. A uniform

Determine the maximum deflection and maximum principal stress for the plate shown in Figure P12-9. The plate is fixed along all three sides. A uniform pressure of 100 MPa is applied to the surface. The plate is made of steel with E = 200 GPa, v = 0.3, and thickness t = 10 mm, Î± = 0.75m and b = 1 m.
Figure P12-9

a/2

Step by Step Solution

★★★★★

3.60 Rating (171 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Figure P129 Displacement Magnit... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

1414-P-T-H-T(1535).docx

120 KBs Word File

Students Have Also Explored These Related Thermodynamics Questions!

A stockroom floor carries a uniform load of p = 80 lb / ft2 over half the floor as shown in Figure P12-12. The floor has opposite edges clamped and remaining edges and midspan simply supported. The...

Determine the maximum deflection and maximum principal stress of the circular plate shown in Figure P12-8. The plate is subjected to a uniform pressure p = 50 kPa and fixed along its outer edge. Let...

A square steel plate (Figure P12-1) of dimensions 20 in. 3 20 in. with thickness of 0.1 in. is clamped all around. The plate is subjected to a uniformly distributed loading of 1 lb/in2. Using a 2 2...

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

The experimental result differs from the assumption. The result shows that the ring oscillator frequencies can be grouped into two groups, where the first group is the high frequency group for the...

( 1 ) A rectangular bar is subjected to uniaxial stretching with a stress 0 . Draw the Mohr's circle for such a loading condition. ( m ) What relationship must be satisfied between the local shear...

In a situation in which data are known to three significant digits, we write $6.379 \mathrm{m}=6.38 \mathrm{m}$ and $6.374 \mathrm{m}=6.37 \mathrm{m} .$ When a number ends in $5,$ we arbitrarily...

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

In the following table, task durations are given in weeks. The estimates were made at the 95 percent level (Calculating Probabilistic Activity Times subsection). a. Find the expected time and...

On Monday, Melody checks her bank balance and has $437.23. She knows that she will get paid on Friday and earn $236.12. She pays her bills, which amount to $582.96. What will Melody's bank balance be...

When completing the reconciliation form, what amount should be listed as the ( + / - ) adjustment to BOOKS on the balance per book's side?

3.57 A quality control supervisor has taken a sample of 16 bolts from the output of a thread-cutting machine and tested their tensile strengths. The results, in tons of force required for breakage,...

A furnace of 70- by 60- by 90-cm inside dimensions is constructed of a material having a thermal conductivity of 0.5 Btu/h ft F. The wall thickness is 6 in. The inner and outer surface temperatures...

The slanted intersection shown in Figure P3-81 involves materials A and B. Write steady state nodal equations for nodes 3, 4, 5, and 6 using Table 3-2(f and g) as a guide. Figure P3-81 10 3 5 11 Ay/2...

A horizontal plate, 25 by 50 cm, is maintained at a constant temperature of 78C and buried in a semi-infinite medium at a depth of 5 m. The medium has an isothermal surface maintained at 15C and a...

Modify your Online Book Order program from week 5 to prompt the users for the number of books they are purchasing. Using a for loop, prompt the user for the cost of each book and store it into a...

Decision tree: The manager for a growing firm is considering the launch of a new product. If the product goes directly to market, there is a 50 percent chance of success. For $120,000, the manager...

A Canada-based investor buys shares of Toronto-Dominion Bank (TD.TO) for C$90.00 on October 15,2007 with the intent of holding them for a year. The dividend rate was C$3.00 per year. The investor...