Find the horizontal deflection Icirc acute h and vertical deflection Icirc acute n at the free end C of the frame ABC shown in the figure (The flexural rigidity EI is constant throughout the frame ) PC

Question: Find the horizontal deflection Î´h and vertical deflection Î´n at the free end C of the frame ABC shown in the figure. (The flexural rigidity

Find the horizontal deflection Î´h and vertical deflection Î´n at the free end C of the frame ABC shown in the figure. (The flexural rigidity EI is constant throughout the frame.)

Step by Step Solution

★★★★★

3.41 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

MEMBER AB Since member BC does not change in length h ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (846).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

The horizontal deflection of the right end of the curved bar of Fig. 412 is given by Eq. (435) for R/h > 10. For the same conditions, determine the vertical deflection.

The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P1 = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF...

The frame shown in the figure consists of a beam ACB supported by a struct CD. The beam has length 2L and is continuous through joint C. A concentrated load P acts at the free end B. Determine the...

Find the horizontal deflection h and vertical deflection v at the free end C of the frame ABC shown in the figure. ( The flexural rigidity El is constant throughout the frame. ) Note: Disregard the...

Q1 A simply supported beam has a concentrated downward force P at a distance of a from the left support, as shown in the figure below. The flexural rigidity EI is constant. Find the equation of the...

Q 1 . Estimate the diameter of bolt required as per five different theories of failure if the bolt is subjected to an pull 1 6 kN and a Shear Force of 1 0 kN . Elastic limit in tension is 3 0 0 N / m...

The post shown in Figure has a flexural rigidity E I and supports a load W at the free end C . Using unit load method, find the horizontal and vertical deflections at C .

2 Deflection methods. An excavated hole is supported by the brace mechanism shown in Figure 2 . The hole is 6 m deep and spans 1 6 meters. The horizontal brace member has pinned connections to steel...

Problem # 1 : ( 7 0 points ) The beam ABC of length 2 L is fixed ( i . e . clamped ) at point A and supported by a roller at B , as shown in Figure 1 ( on the following page ) . The beam is loaded by...

Determine the vertical and the horizontal deflection at the free end of the beam shown in figure. Assume uniform flexural rigidity E I throughout.

Given the following information set up the problem in a transportation table and solve for the minimum-cost plan: PERIOD 1 2 3 Demand 550 700 750 Capacity Regular 500 500 500 Overtime 50 50 50...

The piecewise function graphed below represents the costs of mailing a package (in dollars) as a function of its weight (in ounces). 1.1 + 0.9 0.8 0.70 0.6 0.5 0.4 0.3 0.2 0.1 -0.1+ Complete the...

The formula associated with MM Proposition II without taxes is The formula associated with MM Proposition II without taxes is Multiple Choice O RWACC = RS - RB- O Re = RB - Re- O Re = Rs + (B/S) (RS...

3. Determine the cutoff sample score on the comparison distribution at which the null hypothesis should be rejected. .05 level, df=4: 2 needed=9.488. . A true experiment systematically varies the...

The 2014-T6 aluminum column has the cross section shown. If the column is pinned at both ends and subjected to an axial force $P=100 \mathrm{kN}$, determine the maximum length of the column. 15 mm]...

The 2014-T6 aluminum column is $3 \mathrm{~m}$ long and has the cross section shown. If the column is pinned at both ends and braced against the weak axis at its mid height, determine the allowable...

The column is made of wood. It is fixed at its bottom and free at its top. Use the NFPA formulas to determine the largest allowable axial force $P$ that it can support if it has a length \(L=6...

J. Smythe, Inc., manufactures fine furniture. The company is deciding whether to introduce a new mahogany dining room table set. The set will sell for $6,400, including a set of eight chairs. The...

The face value of a bond is $68,000, its stated rate is 7%, and the term of the bond is five years. The bond pays Interest semiannually. At the time of issue, the market rate is 8%. Determine the...

Rubenstein Bros. Clothing is expecting to pay an annual dividend per share of $0.95 out of annual earnings per share of $3.25. Currently, Rubenstein Bros.' stock is selling for $17.50 per share....