Question: For the open-loop control system described by the block diagram shown in Figure P2.12, determine the value of K such that y(t) 1 as t

For the open-loop control system described by the block diagram shown in Figure P2.12, determine the value of K such that y(t) †’ 1 as t †’ ˆž when r(t) is a unit step input. Assume zero initial conditions.

Controller Process FIGURE P2.12 Open-lcop control system.

Step by Step Solution

★★★★★

3.39 Rating (165 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The openloop transfer function is With Rs 1s we have Th... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

835-C-S-S-A-D (1407).docx

120 KBs Word File

Students Have Also Explored These Related Systems Analysis And Design Questions!

The block diagram shown in Figure PI 1.29 is an example of an interacting system. Determine a state variable representation of the system in the form x(t) = Ax(t) + Ba(t) y(t) - Cx(t) + Du(t) lt 2

Consider the block diagram in Figure CP2.10. Create an m-file to complete the following tasks: (a) Compute the step response of the closed-loop system (that is, R(s) = 1/s and Td(s) = 0) and plot the...

A closed-loop speed control system is subjected to a disturbance due to a load, as shown in Figure DP4.1. The desired speed is Ïd(t) = 100 rad/s, and the load disturbance is a unit step input...

P2.12 For the open-loop control system described by the block diagram shown in Figure P2.12, determine the value of K such that y(t) 1 as to when r(t) is a unit step input. Assume zero initial...

P 2 . 1 2 For the open - loop control system described by the block diagram shown in Figure P 2 . 1 2 , determine the value of K such that y ( t ) 1 as t when r ( t ) is a unit step input. Assume...

For the open-loop control system described by the block diagram shown in Figure P2.12, determine the value of K such that y(t) 1 as to when r(t) is a unit step input. Assume zero initial conditions....

Objective: Design a controller for the heading control of the aircraft system represented by the block diagram shown in figure 1. a) Determine the minimum value of the gain K when Gc(s)-K, so that...

System analysis using Matlab A vehicle suspension system can be modelled by the block diagram shown in Figure 1 below: Body mass m2 Spring of stiffness ks Damper of coefficient cs X Wheel mass, m1...

Q1. Consider the liquid-level control system shown in Figure 1, where R1 and R2 are water resistances, C1 and C2 are the capacitance of tanks 1 and 2, respectively. A proportional controller is added...

signal and system related problems need you guidelines Analysing a simple system A vehicle suspension system can be modelled by the block diagram shown in Figure 1 below: Body mass Spring of Jumpercl...

Al Gore (an American politician and environmentalist) and many others have spent years trying to influence everyone globally to think about the changes in the environment and the implications of...

2. A car will drive when the ignition is ON, and the following conditions are satisfied: A safety door is closed. i. ii. A driver's seatbelt is put ON. The car will not drive, and an LED-lamp on the...

( A ) Which of the listed general ledger accounts might appear on a corporation's balance sheet? Sales Reventue Cost of Goods Sold Salaries Payable Office Expense

Referring to Exercise 5, imagine the hypothesis of no interactions is rejected. Is it reasonable to conclude that the interaction is disordinal?

List the six activities of systems analysis.

What are three types of models?

What is the difference between functional requirements and nonfunctional requirements?

b course hero - Bing X Homework Help - Q&A from On x Bb WileyPLUS Online Homework - E X NWP Assessment Builder UI App X NWP Assessment Player UI Appli X + X @...

Butterfly Tractors had $18.00 million in sales last year. Cost of goods sold was $8.80 million, depreciation expense was $2.80 million, interest payment on outstanding debt was $1.80 million, and the...

2. Why is regulation important