Question: For the same material and thickness as in Problem 7.66, estimate the force required for deep drawing with a blank diameter of 10 in. and

For the same material and thickness as in Problem 7.66, estimate the force required for deep drawing with a blank diameter of 10 in. and a punch diameter of 9 in.

Step by Step Solution

★★★★★

3.34 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Calculate the force required for deep drawing as shown below Where F... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

972-E-M-E-B-D (643).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

By modern standards, the shaft design of Prob. 523 is poor because it is so long. Suppose it is redesigned by halving the length dimensions. Using the same material and design factor as in Prob. 523,...

Two strings are made of the same material and have waves of equal speed. String 1 is thick; string 2 is thin. (a) Is the tension in string 1 greater than, less than, or equal to the tension in string...

For the cylindrical vessel with ellipsoidal heads shown in Figure P9-22a under loading p = 500 psi, determine if the vessel is safe against yielding. Use the same material and factor of safety as in...

A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its inside diameter = 100 mm. The sheetmetal thickness = 2 mm. If the blank diameter = 225 mm, determine: (a)...

Please quality check my solutions for this advanced heat transfer problem. Show all work. Thank you. All original documents are located at the bottom. 3.9 COMPACT HEAT EXCHANGERS 3.9.10-1 3.9.10...

Course: Facilities Layout Planning Abstract This project illustrates a full design from the scratch for the lifting jack starting from the product, process and schedule design. Followed by Flow,...

Q 1 . A deep drawing operation is performed on a sheet - metal blank that is 0 . 1 2 5 mm thick. The height of the cup = 1 5 5 m m and its diameter = 1 0 0 m m ( both inside dimensions ) . ( a )...

(20 pts) 3. A cup-drawing operation is performed in which the punch diameter = 80 mm, the punch and die radii = 4 mm, the sheet thickness = 3 mm, and the blank diameter = 150 mm. The sheet metal has...

A cylindrical cup is produced in a drawing operation. The blank diameter is 1 6 0 mm , and the thickness of the sheet metal is 2 mm . The cup height is 6 0 mm , and the punch diameter is 8 0 mm . The...

A deep drawing operation is performed in which the inside of the cylindrical cup has a diameter = 4.0 inches and a height = 2.5 inches. The stock thickness = 1/8 inch, and the starting blank diameter...

how long does the ball take to reach from point a to point b? The ball's mass is 100 grams, the initial velocity of the ball is 0m/s, and static and kinetic friction coefficients are 0.4, and 0.3...

Two TKSRs with a volume of 400 cm3 are connected in series. The feed concentration is 0.6 molA / L. When the feed rate is 10 cm3 / min, the outlet concentration of the first tank is 0.1 molA / L,...

What is base pay?

Understanding M1 and M2. If you write a check from your checking account to your money market account, what happens to M1 and M2?

Find the frequency domain impedance, Z, for the network shown. j5Q 3.75

Find the frequency domain impedance, Z, for the network shown. 5 10

Find Z(j) at a frequency of 60 Hz for the network shown 2 4 500F 0

An urgent!, urgent! and urgent! Challenging University of Cumberland Case study A and statistics question. 2. Find the probability that a normal random variable X with mean m = 1,600 and standard...

6. (1.5 pt) Bob and Ann both make optimal portfolio allocations. Bob has $ 1000 to invest, Ann has $ 2000 to invest. There are 3 assets that they can invest in: a risk free asset with a rate of...

Kenneth secured a 4 - year car loan at 5 . 6 0 % compounded annually that required him to make payments of $ 8 8 2 . 8 1 at the beginning of each month. Calculate the cost of the car if he made a...