Question: A shearing pin is designed to break and disengage gears before damage is done to a machine. In a test, a vertically upward force of

A shearing pin is designed to break and disengage gears before damage is done to a machine. In a test, a vertically upward force of 8250 lb and a 7520 lb at 35.0° below the horizontal are applied to a shearing pin. What is the resultant force?

Step by Step Solution

★★★★★

3.38 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

To find the resultant force we need to combine the two forces using vector ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Basic Technical Mathematics Questions!

In 2001, Donald Malen purchased a Yard-Man riding mower at a Home Depot store. The mower was manufactured by MTD Products in 1998 and was advertised as "Reconditioned Power Equipment" with a "Full...

A skateboarder with his board can be modeled as a particle of mass 76.0 kg, located at his center of mass (which we will study in Chapter 9). As in Figure P8.67, the skateboarder starts from rest in...

A 100-lb force directed vertically downward is applied to the toggle vise at C. Knowing that link BD is 6 in. long and that a = 8 in., determine the horizontal force exerted on block E. 100 lb 6 in....

a shearing pin i designed to break gears before damage is done to a machine. in a test a vertically upward for of 8 2 5 0 N and a 7 5 2 0 N at 3 5 \ deg below the horizontal are applied to a shearing...

The Hu . ma . ne AI pin is designed to be a "Screenless, Seamless, Sensing" device. Is this true? Group of answer choices True False

Traditional quality control methods identify variation as the enemy of ensuring quality. However, the control of variation by itself can never achieve the remarkably low nonconformance rates of...

Statistical Process Control at Motorola: Traditional quality control methods identify variation as the enemy of ensuring quality. However, the control of variation by itself can never achieve the...

A mechanical connection known as a clevis and pin is shown. The dimensions of the assembly are given as: a = 2 2 mm b = 3 3 mm c = 9 mm d = 1 5 mm t = 1 3 mm W = 3 4 mm L = 8 2 mm In order to avoid...

PART A - TESTING OF SHEAR CONNECTIONS SINGLE SHEAR CONNECTIONS a. b. C. Check the diameters of the aluminum (2011-T3) test pins and record in the following table (nominal diameter is 3/16 in = 0.188...

Two horizontal 7 . 5 - kip forces ( P ) are applied to pin B of the assembly shown. A 0 . 8 - in . diameter pin is used at each connection. Problem 0 1 . 0 6 1 . a - Shearing stress at a pinned joint...

Rick DeNeefe, manager of the Golden Valley Bank credit authorization department, recently noticed that a major competitor was advertising that application for equity loans could be approved within...

On June 30, 2015, the shareholders equity of Fabinet, a foreign corporation, was 10,500,000 FC. At that time, Newcore, a U.S. corporation, acquired 40% in Fabinet by paying $3,120,000 when 1 FC was...

Question 1 2 AL Jose now has $ 5 0 0 . How much would he have after 6 years if he leaves it inv annual compounding? $ 7 2 3 . 8 9 $ 6 8 9 . 4 2 $ 6 5 4 . 9 5 $ 6 2 2 . 2 0 $ 6 6 5 . 0 0 Question 1 3

The effects of developer strength (A) and development time (B) on the density of photographic plate film are being studied. Three strengths and three times are used, and four replicates of a 32...

Refer to Table 8.17 from the 1991 General Social Survey. White subjects were asked: (B) Do you favor busing of (Negro/Black) and white school children from one school district to another?, (P) If...

Refer to Section 8.3.2. Explain why software for which parameters sum to zero across levels of each index reports 11 AC = 22 AC = 0.514 and 12 AC = 21 AC = 0.514, with SE = 0.044 for each term.

Table 8.18 refers to automobile accident records in Florida in 1988. a. Find a loglinear model that describes the data well. Interpret associations. b. Treating whether killed as the response, fit an...

Required information The following information applies to the questions displayed below] The following information is available for ADT Company. which produces speciat-order secunty procucts and uses...

Saturn issues 6.5%, five-year bonds dated January 1, 2011, with a $500,000 par value. The bonds pay interest on June 30 and December 31 and are issued at a price of $510,666. The annual market rate...

TUTIONS w . ESCLETE 1980 UULUU... TUTIONS w . ESCLETE 1980 UULUU