Question: Compare the thickness required for a 2 m diameter flat plate, designed to resist a uniform distributed load of 10 kN/m 2 , if the

Compare the thickness required for a 2 m diameter flat plate, designed to resist a uniform distributed load of 10 kN/m2, if the plate edge is

a. Completely rigid; 

b. Free to rotate. 

Take the maximum allowable stress for the material as 100 MN/m2 and Poisson’s ratio for the material as 0.3.  

Step by Step Solution

★★★★★

3.28 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Thickness required for a 2 m diameter flat plate Assuming completely rigid edges The thickness of th... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Design Questions!

Q:

A 5 0 . 0 - kg child stands at the rim of a merry - go - round of radius 2 . 4 0 m with her hands free, rotating with an angular speed of 3 . 6 5 rad / s . What is the magnitude of the static...

Q:

A cylindrical tank 80 cm in diameter and 2.0 m high contains water at 80C. The tank is 90 percent full, and insulation is to be added so that the water temperature will not drop more than 2C per...

Q:

A combined cycle power plant is designed with four-150 MW gas turbines and one-350 MW steam turbine. The exhaust gases from each gas turbine pass through a supplementary firing chamber. Then the...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Calculate the load - carrying capacity of a rectangular steel plate with dimensions 5 0 0 mm x 3 0 0 mm x 1 0 mm under uniform loading conditions. Determine the ultimate load capacity of a pile with...

Q:

Vanderwaal Company uses a standard costing system. In August, 5,300 actual labor hours were worked at a rate of $12.50 per hour. The standard number of hours is 5,275 and the standard wage rate is...

Q:

Seaside issues a bond that has a stated interest rate of 10%, face amount of $50,000, and is due in 5 years. Interest payments are made semi-annually. The market rate for this type of bond is 12%....

Q:

Understanding levels of significance. Explain in plain language why a significance test that is significant at the 1% level must always be significant at the 5% level.

Q:

=+Chapter 4 Completing the Accounting Cycle 197 May 17. Recorded cash from cash clients for fees earned during the period May 116, $8,200. 20. Purchased supplies on account, $400. 21. Recorded...

Q:

Estimate the optimum pipe diameter for a water flow rate of 10 kg/s, at 20C. Carbon steel pipe will be used. Density of water 1000 kg/m 3 .

Q:

Estimate the shaft work required to pump 65 gal/min of sugar solution in water (specific gravity = 1.05) if the pump inlet pressure is 25 psig and the outlet pressure required is 155 psig.

Q:

Estimate the safe working pressure for a 4 in. (100 mm) dia., schedule 40 pipe, SA53 carbon steel, butt welded, working temperature 100C. The maximum allowable stress for butt welded steel pipe up to...

Q:

please explain how data collected from any source document you choose finds its way to the general ledger. Are there any exceptions?

Q:

Weldon Industrial Gas Corporation supplies acetylene and other compressed gases to industry. Data regarding the store's operations follow: Sales are budgeted at $360,000 for November, $380,000 for...

Q:

ANSWER ALL PLEASE AND THANK YOU B8 MULTIPLE CHOICE 12-35 Stein Company makes carpets. A customer wants to place a special order for 1,000 carpets in navy blue with the company logo woven in the...