A 30-cm-diameter, 1.2 kg solid turntable rotates on a 1.2-cm diameter, 450 g shaft at a constant
Question:
A 30-cm-diameter, 1.2 kg solid turntable rotates on a 1.2-cm diameter, 450 g shaft at a constant 33 rpm. When you hit the stop switch, a brake pad presses against the shaft and brings the turntable to a halt in 15 seconds. How much friction force does the brake pad apply to the shaft?
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 87% (8 reviews)
Model Assume there are no other forces or torques other than the brake pad Vi...View the full answer
Answered By
Akshay Singla
as a qualified engineering expert i am able to offer you my extensive knowledge with real solutions in regards to planning and practices in this field. i am able to assist you from the beginning of your projects, quizzes, exams, reports, etc. i provide detailed and accurate solutions.
i have solved many difficult problems and their results are extremely good and satisfactory.
i am an expert who can provide assistance in task of all topics from basic level to advance research level. i am working as a part time lecturer at university level in renowned institute. i usually design the coursework in my specified topics. i have an experience of more than 5 years in research.
i have been awarded with the state awards in doing research in the fields of science and technology.
recently i have built the prototype of a plane which is carefully made after analyzing all the laws and principles involved in flying and its function.
1. bachelor of technology in mechanical engineering from indian institute of technology (iit)
2. award of excellence in completing course in autocad, engineering drawing, report writing, etc
4.70+
48+ Reviews
56+ Question Solved
Related Book For
Physics for Scientists and Engineers A Strategic Approach with Modern Physics
ISBN: 978-0133942651
4th edition
Authors: Randall D. Knight
Question Posted:
Students also viewed these Physics questions
-
A 200 g, 40-cm-diameter turntable rotates on frictionless bearings at 60 rpm. A 20 g block sits at the center of the turntable. A compressed spring shoots the block radially outward along a...
-
A heating section consists of a 30 cm diameter duct which houses a 6 kW electric resistance heater. Air enters the heating section at 1 atm, 15oC and 33% relative humidity at velocity 8.5 m/s....
-
A 30-cm diameter pipe carries H2O at a rate of 10 kg/s. At a certain cross-section, steam is found to be saturated vapor at 200oC. Determine (a) The pressure (kPa). (b) Velocity (m/s).
-
Jackson Corporation has borrowed $2 million from a local bank under a long-term debt agreement whereby the loan has to be repaid in two years' time. The agreement was violated and the debt became...
-
Zhang Machine & Dye bought a machine on January 2, 2014, for $460,000. The machine was expected to remain in service for three years and produce 2,000,000 parts. At the end of its useful life,...
-
a. Find the profit-maximizing quantity of L. b. Find the profit-maximizing quantity of q. c. What is the maximum profit? d. Suppose now that the firm is taxed $30 per unit of output and that the wage...
-
What images of closers did you have before reading this chapter? List as many negative stereotypes of closing as you can. How has the chapters point that closing should become a natural part of the...
-
Clothes, Inc., has an average annual demand for red, medium polo shirts of 25,000 units. The cost of placing an order is $80 and the cost of carrying one unit in inventory for one year is $25....
-
Pick any product that is sold in local Canadian market and you are planning to sell it in a country of your choice. Please elaborate on how you will decide on following factors: 1) Adaption method...
-
An air base of 3205 ft exists for a pair of overlapping vertical photographs taken at a flying height of 5500 ft above MSL with a camera having a focal length of 152.4 mm. Photo coordinates of points...
-
The 2.0 kg, 30-cm-diameter disk in Figure P12.66 is spinning at 300 rpm. How much friction force must the brake apply to the rim to bring the disk to a halt in 3.0 s? Brake FIGURE P12.66
-
Your engineering team has been assigned the task of measuring the properties of a new jet-engine turbine. Youve previously determined that the turbines moment of inertia is 2.6 kg m 2 . The next job...
-
Other chromosomes have sequences as follows: (a) 1 2 5 6 7 8; (b) 1 2 3 4 4 5 6 7 8; (c) 1 2 3 4 5 8 7 6. What kind of chromosome change is present in each? Illustrate how these chromosomes would...
-
What is political skill and what are the four facets to political skill?
-
What is the grapevine? Of what value is it to the organization? What are the pros and cons?
-
What is the relevance of Houses pathgoal theory to managers?
-
Compare and contrast the five bases of power.
-
What is sexual harassment and what can organizations do to prevent it?
-
Consider again the model economy described in Exercise 3.2, but suppose there is a second storable good, silver. Silver is as easy to exchange and store as gold. The initial old own a total of 50...
-
What steps must a business take to implement a program of social responsibility?
-
A large number of long tubes, each of diameter D, are placed parallel to each other and at a center-to-center distance of s. Since all of the tubes are geometrically similar and at the same...
-
A dryer is shaped like a long semicylindrical duct of diameter 1.5 m. The base of the dryer is occupied with water soaked materials to be dried, and maintained at a temperature of 370 K and...
-
Two parallel back disks are positioned coaxially with a distance of 0.25 m apart. The lower disk is 0.2 m in diameter and the upper disk is 0.4 m in diameter. If the lower disk is heated electrically...
-
1. What is service-oriented architecture and how is it different from Web services architecture? 2. What is the role of the systems approach in the SDLC? 3. Briefly discuss the key phases of the SDLC...
-
1. Define the role of CRM in your own words. 2. What are the key differences between todays CRM and the early generation of CRMs? 3. How does CRM impact the companys bottom line or performance? 4....
-
What do you think are Thorndike's major contributions to learning theory and teaching? Share a time when you have observed Connectionism. How useful do you think the theory of Connectionism is in an...
Study smarter with the SolutionInn App