Question: 1 . For the floor framing plan shown below, find the required M n for: a . Typical interior beam b . Edge beam c

1. For the floor framing plan shown below, find the required Mn for:
a. Typical interior beam
b. Edge beam
c. Typical interior girder
d. Edge girder
Assume the following dead loads:
Floor Deck =20psf
Beams =50plf
Girders =100plf
Floor live load =50psf(Lo- Unreduced)
2. If the typical interior beam in question #1 has capacity Mn=220kip - ft , what is the maximum Lo
it can resist?
3. For the roof framing plan shown below, find the required Mn for:
a. Typical interior beam
b. Edge beam
c. Typical interior girder
d. Edge girder
Assume the following dead loads:
Roof Deck =15psf
Joists =20plf
Beams =50plf
Partial Roof Framing Plan
1 . For the floor framing plan shown below, find

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Produce a work breakdown structure for the minor dwelling project plan ( the image files provided) using ms word or another software. The work breakdown structure should have 4 hierarchy levels with...

Q:

R In this assignment, you will be examining the framing elements for a proposed three story precast concrete office building and the various loads that are expected to act on them. You will use the...

Q:

For the building described on the following pages, calculate the loads and draw a factored beam loading diagram (FBD), a factored shear diagram, and a factored moment diagram for each of the...

Q:

Thank u guys:) This is the reference pages but the questions are the last 3 pictures . . . . Craft - Mason Wage rate VET $29.00 Hours worked 50 hours per week for 20 weeks and 40 hours per week for...

Q:

6. A garage floor is sloped _" per foot for proper drainage. A. 1/8" to 1/4 B. 1/4" to 3/4 C. 3/4" to 1 . 4 7. Control joints should be provided at a maximum of _" intervals in both directions on a...

Q:

You are required to complete a detailed design of an office building. The geometry of the building is shown in Figures 3 and 4. Figure 3 shows an elevation view while Figure 4 shows a typical...

Q:

Final Estimating Project You are employed by a contactor that is replying to a tender for a small garage project in a small township in Northern Ontario. Your assignment is to compete an estimate of...

Q:

Activity 6-3-Footing Forms Refer to Print 6-3 and Quantity Spreadsheet No. 6-3 in the online learner resources. Calculate the linear feet of metal forms required for the footings. In addition,...

Q:

\ table [ [ H , H , H ] , [ H , H , H ] , [ H , , H ] , [ H , H , H ] ] Fig. 3 Fig. 4 Fig. 5 shows construction detalls of the retrofitting Fig. 5 DETAIL. AProblem 3 Given an existing two - story...

Q:

Nissan Motor Company, Ltd.: Target Costing System Nissan Motor Company, Ltd. (Nissan) was by 1990 the world's fourth-largest automobile manufacturer. In 1990, Nissan produced just over 3 million...

Q:

Discuss the concepts of production value, transformation and operations planning as they apply now, or may in the future, to the production of Gulaks Uno. Could any of these factors be reasons why...

Q:

Producers' surplus. Interpret the results of Problem 68 with both a graph and a description of the graph.

Q:

One assumption of CVP analysis is that all costs can be classified as either variable or foxed. True Falce

Q:

Time-Warner Cable auto-scans the packets that are delivered by its wires to screen for known malicious viruses that would impair the functioning of the network. It has not sought consent from its...