Question: 1 - Study the stability of the closed loop system below: with C ( s ) = k s + 1 0 0 and G

1- Study the stability of the closed loop system below:
with C(s)=ks+100 and G(s)=10(s+20)2
2- Draw the root locus of the closed loop system in figure 1(Show the different steps):
1 - Study the stability of the closed loop system

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

P 3 . ( 6 0 marks ) Consider a closed loop system comprising of system 1 and system 2 given in the configuration shown in Figure 1 . The open loop response of system 1 and system 2 to step inputs are...

Q:

Figure on the right shows the schematic description of a system consisting of two gravity tanks in series. The fluid enters tank 1 at a flow rate of F0(m3/s). The level of fluid in tank 1 is L1(m)....

Q:

WE USE System given below. D Ga Ya Y sp E U Km Y, GC G Popuko-oh G Ym Gm - 1 1 + 108 +! where Ev (s) kv Eusti Gps). apst! Gm (s) = km Ensti Gars) = CS Scanned with CamScanner Edsti km = 5 (ie ca o (...

Q:

Consider the tank heater system shown in the figure below. In this system a liquid enters the tank with a flowrate F1(m3/min) and a temperature T1(K), where it is heated by using an electric heater....

Q:

Root Locus For the unity feedback system shown, sketch the root locus as a function of k and A . Discuss the stability of the closed loop system as a function of the gain k . B . Find the value of...

Q:

In a system where the liquid level is controlled, the system's inlet is shown by R(s) and its output by C(s). R(s) C(s) Ge(s) G(s) The transfer function of the system has been subtracted as G(s)....

Q:

help 2 . In most manufacturing welding situations, uncertainties in dimensions of the part, geometry of the joint and welding process itself require the use of sensors to maintain weld quality....

Q:

Q3. Liquid flows into a tank whose height is due to be controlled. The input flow is regulated by a valve. A flow of 3 m3/sec is produced for 1 mm change in the valve position. The valve has a dead...

Q:

For a first-order plus deadtime (FOPDT) process, a PI controller is used. The transfer functions for the closed loop system are given as follows: Ge(s)=K (1+), G(S)=Kpe-Ops , Ga(S)=G(S)=1 TpS+1...

Q:

Question 21 Not yet answered Analyse the systems given below and identify the type of system as either closed loop or open loop. (2.5 Marks) S.no System Open Loop Closed Loop Marked out of 2.50 P...

Q:

Let u, v R be two real valued functions defined on an open set C R satisfying the following: (i) All the partial derivatives of u and u up to second order exist and are continuous at all points of ....

Q:

Hello there , please assist with the following The attachment provides an extract of the job descriptions of three positions: A) a matre d (dining room manager), B) a captain (dining room...

Q:

The discounted payback decision technique uses a statistic or metric denominated in no units or unitless ( e . g . 1 . 8 2 ) a percentrge ( eg . 1 2 . 2 5 % ) years ( e . g . 4 . 2 5 years ) eurrency...

Q:

Suppose Intel stock has a beta of 0.79, whereas Boeing stock has a beta of 1.2. If the risk-free interest rate is 5.3% and the expected return of the market portfolio is 10.4%, according to the CAPM,...