Question: 3. The transfer function of a system is given as G(S) = K (TS+2)(TS+2) Determine the stability, damping and final value of the system

3. The transfer function of a system is given as G(S)

3. The transfer function of a system is given as G(S) = K (TS+2)(TS+2) Determine the stability, damping and final value of the system

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

Q:

Question 16 Not yet answered Transfer Function of a system is given below Marked out of 5.00 25 Flag question C(s) R(S) s +15 s +25 a. Draw the poles of the system. (1 Mark) b.Write step response...

Q:

Q1 If closed loop transfer function of a system is given as K (2-s) 2 {tps +(2T +1)s +K (2s)+2} P G (s) = Where Tp P is the time constant, Kc is the gain of the proportional controller. It is given...

Q:

I need to answer for (e)(f)(g)(h). Thank you! Consider the open-loop plant: 10 P(s) = (s2 + 2s +5) and a controller: kls +1) C(s) = $(8 + 2) structured in a unity feedback control architecture: w u...

Q:

Problem 2 - Stability Consider the open-loop plant: 10 P(s) (32 +2s +5) and a controller: C($) k(s+1) s(s+2) structured in a unity feedback control architecture: u C(s) P(s) Y(8) (a) (by hand)...

Q:

First Order System: K G(S) TS + 1 Unity-Gain Second Order System: wa G(S) 52 + 25 + wa Unit step response of unity-gain underdamped second order system: c(t) = 1 e-twnt cos(WnV1 - 32+ - ) where 0 =...

Q:

Figure 1 shows a system that controls the roll angle of an airplane, with frictional losses ignored. If proportional control were used, the two poles at s = 0 would split off at +90 angles, and the...

Q:

1- [a] For positive values of K, plot the root locus for a unity negative feedback control system having the following open-loop transfer function: K G(s) =- (s+1)(s+4)(s+7) For what values of gain K...

Q:

For the single link robot arm system given in Figure 1 mass of the system is m, and length is 1. The angle between the robot and ground is 0. The angular velocity is . Control torque applied at the...

Q:

Problem 1 : Consider the closed - loop control system shown in the figure. 1 . Using MATLAB, 1 . 1 . Derive the open - loop transfer function of the system. 1 . 2 . Plot a root - locus diagram for...

Q:

signal and system related problems need you guidelines Analysing a simple system A vehicle suspension system can be modelled by the block diagram shown in Figure 1 below: Body mass Spring of Jumpercl...

Q:

The Paddocks hired Harper Realty to sell their hotel. The Paddocks agreed that if Harper sold the hotel, they would pay Harper a commission of $ 15,000, with $ 3,000 down and the balance in monthly...

Q:

Marshall Company discovers in 2014 that its ending inventory at December 31, 2013, was $5,000 under-stated. What effect will this error have on (a) 2013 net income, (b) 2014 net income, and (c) The...

Q:

When considering why to buy annulties, which of the following statements is correct? Mutiple Choice It is better to find a variable annuty before fully funding your iRA, Keogh, or 4 0 1 0 4 . It is...

Q:

CT Corp Comprehensive Question Canadian Tire Corporation, Limited ( Canadian Tire ) is a family of companies that includes a retail segment and a financial services division, among others. The retail...

Q:

Develop clear policy statements.

Q:

Draft a business plan.

Q:

Describe the guidelines for appropriate use of the direct plan.