7. Determine the p-value that determine if higher stirring would produce greater Powder Density. Leave your...

Transcribed Image Text:

7. Determine the p-value that determine if higher stirring would produce greater Powder Density. Leave your answer in 3 decimal places. Open block draw 0.020 8. Using 5% level of significance, determine the critical value of the rejection region that determine if higher stirring would produce greater Powder Density. Leave your answer as a positive value and round the answer to 3 decimal places. 1.830 9. Determine the p-value that determine if higher stirring would produce lower surface area. Leave your answer in 3 decimal places. 0.929 10. Using 5% level of significance, determine the critical value of the rejection region that determine if higher stirring would produce lower surface area. Leave your answer as a positive value and round the answer to 3 decimal places. 0.0137 Since stirring rate (Factor C) is invalid for One-Way ANOVA and the experimenter strongly suspects that higher stirring would produce greater Powder Density and higher stirring rate would produce lower Surface Area. In addition, the Surface Area of silver powder may be different in each production batch. The experimenter decides to obtain more data on powder density and surface area from different stirring rates, but only at two levels (100 RPM and 200 RPM). The data is shown below. You may assume that both powder density and surface area are normally distributed. Powder Density Surface Area Batch 100 RPM 200 RPM 100 RPM 200 RPM 1 14.80 13.91 0.4430 0.4486 2 14.43 14.85 0.4098 0.4361 3 14.33 14.90 0.4285 0.4311 14.60 16.20 0.4317 0.3888 5 14.49 15.89 0.4454 0.4557 6 15.02 15.83 0.4183 0.4037 7 13.93 15.35 0.4325 0.4509 8 15.37 17.83 0.4614 0.4343 9 14.68 15.56 0.4551 0.4292 10 14.64 16.99 0.4417 0.4496 11 14.13 13.81 0.4265 0.4309 12 14.22 17.62 0.4468 0.4348 Open block drawer 13 15.09 14.08 0.3902 0.4460 7. Determine the p-value that determine if higher stirring would produce greater Powder Density. Leave your answer in 3 decimal places. Open block draw 0.020 8. Using 5% level of significance, determine the critical value of the rejection region that determine if higher stirring would produce greater Powder Density. Leave your answer as a positive value and round the answer to 3 decimal places. 1.830 9. Determine the p-value that determine if higher stirring would produce lower surface area. Leave your answer in 3 decimal places. 0.929 10. Using 5% level of significance, determine the critical value of the rejection region that determine if higher stirring would produce lower surface area. Leave your answer as a positive value and round the answer to 3 decimal places. 0.0137 Since stirring rate (Factor C) is invalid for One-Way ANOVA and the experimenter strongly suspects that higher stirring would produce greater Powder Density and higher stirring rate would produce lower Surface Area. In addition, the Surface Area of silver powder may be different in each production batch. The experimenter decides to obtain more data on powder density and surface area from different stirring rates, but only at two levels (100 RPM and 200 RPM). The data is shown below. You may assume that both powder density and surface area are normally distributed. Powder Density Surface Area Batch 100 RPM 200 RPM 100 RPM 200 RPM 1 14.80 13.91 0.4430 0.4486 2 14.43 14.85 0.4098 0.4361 3 14.33 14.90 0.4285 0.4311 14.60 16.20 0.4317 0.3888 5 14.49 15.89 0.4454 0.4557 6 15.02 15.83 0.4183 0.4037 7 13.93 15.35 0.4325 0.4509 8 15.37 17.83 0.4614 0.4343 9 14.68 15.56 0.4551 0.4292 10 14.64 16.99 0.4417 0.4496 11 14.13 13.81 0.4265 0.4309 12 14.22 17.62 0.4468 0.4348 Open block drawer 13 15.09 14.08 0.3902 0.4460