Question: A 1 4 kip load is applied at A to rigid bar ABC.ABC and DEF are rigid bars. B E and F H are A

A 14 kip load is applied at A to rigid bar ABC.ABC and DEF are rigid bars. BE and FH are
A-36 steel cables (with cross-sectional area =0.50in2) connecting the rigid bars to each
other, spring DG, and a nylon shear block at H. Determine the vertical displacement of
point A. Provide your answer out to 4 digits beyond the decimal.
A 1 4 kip load is applied at A to rigid bar

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

The open end of a cylindrical tank 2 ft in diameter and 3 ft high is submerged in water as shown. If the tank weights 250 lb, to what depth h will the tank submerge? The air barometric pressure is...

Q:

HW 0 1 MEMT 2 1 2 Last Revised 9 / 4 / 2 4 ( adapted from Hibbeler 1 0 t h ed . probs. 4 - 3 1 & 4 - 3 2 ) Eight A 9 9 2 steel, 1 inch diameter, reinforcing rods are embedded into high strength...

Q:

A load P will be supported by a structure consisting of a rigid bar ABCD, a steel A load P will be supported by a structure consisting of a rigid bar ABCD, a steel { : F ] bar ( 1 ) and an aluminum...

Q:

The pin - connected structure shown in the figure consists of a rigid bar ABCD and two aluminum alloy E = 7 0 GPa bars, each with a Part 4 Determine the compatibility equation and rearrange it find...

Q:

As a structural engineer, you are in charge of the design of a structure consisting of a rigid beam ACE that is subjected to the load P and suspended at points A , C , and E by three suspender bars A...

Q:

Rigid bar ABCD is supported by a pin connection at A and by two axial bars ( 1 ) and ( 2 ) . Bar ( 1 ) is a 2 8 - in . - long bronze [ E = 1 4 8 0 0 ksi, [ : = 9 . 7 1 0 - 6 F } bar with a cross -...

Q:

A pin - connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars ( 1 ) and ( 2 ) are both made from steel = 2 8 7 0 0 ksi and...

Q:

The pin - connected structure shown in the figure consists of a rigid bar ABCD and two axial members. Bar ( 1 ) is steel [ E = 2 0 0 GPa , = 1 1 . 7 1 0 - 6 C ] with a cross - sectional area of A 1 =...

Q:

( 4 ) The pin - connected structure shown in the Figure below consists of a rigid bar ABCD and two axial members. Bar ( 1 ) is bronze ] with a crosssectional area of A 1 = 6 2 0 m m 2 . Bar ( 2 ) is...

Q:

Question 2: (50 points) In the assembly shown below, the links AB and CD, which support the rigid member BC, are both made of aluminum (E = 75 GPa) and have each a cross-sectional area of 125 mm. If...

Q:

The composite bar system in Figure 1.48 consists of a steel bar and a bronze bar that are both securely attached to a rigid block and rigid supports. The system is loaded with a total load P at the...

Q:

A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has...

Q:

Valley Company faced the following situations. Journalize the adjusting entry needed at December 31, 2014, for each situation. Consider each fact separately. a. The business has interest expense of...

Q:

coupon rate ( red ) 9 . 4 , market price 7 9 . 7 5 , 2 3 days since last interest, ( RED ) $ 9 . 3 5 commission per bond, 1 5 BONDS PURCHASED. Calculate the accrued interest ( in $ ) and the total...

Q:

Please answer with reason for all why the option is correct and why the other options are incorrect,, Please help with this Accounting type Question: The current ratio is ratio between: A . Current...