Question: A machine foundation can be idealized to a mass-spring system, as shown in Figure 2.4. Given Weight of machine + foundation = 400 KN

A machine foundation can be idealized to a mass-spring system, as shown

A machine foundation can be idealized to a mass-spring system, as shown in Figure 2.4. Given Weight of machine + foundation = 400 KN Spring constant = 100,000 kN/m Determine the natural frequency of undamped free vibration of this foundation and the natural period. Determine the static deflection of this foundation?

Step by Step Solution

★★★★★

3.45 Rating (168 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Given Weight of machine foundation say W 400 kN Spring constant k 100000 kNm i... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Accounting Questions!

A spring exhibits a force-versus-displacement characteristic as shown in Figure E2.11. For small deviations from the operating point x0, find the spring constant when x0 is (a) -1.4; (b) 0; (c) 3.5....

A system has a block diagram as shown in Figure AP2.2. Determine the transfer function T(s) = Y2(s) / R1(s) It is desired to decouple Y2(s) from R1(s) by obtaining T(s) = 0. Select G5(s) in terms of...

A system has a block diagram as shown in Figure P3.26. Determine a state variable model and the state transition matrix Î¦(s). R(s) Msi 25 FIGURE P3.26 Feedback system

A gear and shaft system is shown in Figure 8. The left end of the shaft is coupled to an electric motor, and the right end is free. Load components applied by the mating gear are shown in the figure....

Converting Distributed Loads to Equivalent Point Loads Question 1 {1 point] Convert the distributed load shown in Figure 1 into an equivalent point load, as shown in Figure 2. Figure 1. Distributed...

2. Multiplication of two 4-bit numbers (as shown in Figure 1) can be implemented as a Wallace tree multiplier (as shown in Figure 2) by using carry saver adders. Figure 1. Multiplication of two 4-bit...

Please help with the discussion below: ** Each of the 3 questions below only need to beabout two-threepara graphs but packed full of information, no fluff. **Attached below are a few readings from...

Consider the undamped free vibration represented by the block and spring model in the figure below. The time-dependent path of motion of the block can be given by kx = m(d2x/dt2). This equation can...

(a) The response of an oscillator with mass $m=1$ kg is shown in Figure 3.51. What can you say about the properties of the oscillator and the response? Determine the equation of motion and the...

I have attached the case study and the rubric for this. can I get help here to organzie an answer? CATERPILLAR, INC: THE IMPACT OF DECISION BIASES AND RISK ON CAPITAL BUDGETING Timothy D. West...

Suppose the government is making a $24,000,000,000 expenditure for travel to Mars. If 73% of this amount is spent again, and so on, what is the total effect on the economy? [8.3]

What pressure difference does a 10 m column of atmospheric air show?

Which of the following was the primay purpose of the Organization for Economic Cooperabon and Development Convention on Britery? to combat corporate corruption to protect corporate bribery...

Find a general solution. Show the details of your work. y'1 = 4y1 - 8y2 + 2 cosh t y'2 = 2y1 -6y2 + cosh t + 2 sinh t

Locate the centroid of the region bounded by the given curves. Triangle with vertices at A(5, 1), B(1,3), C(-1, -2) (1,3) A (5,1) (-1,-2)

Locate the centroid of the region bounded by the given curves. about a axis, y? = x, y = x? y = x? y = x

1) Use the given values of n and p to find the minimum usual value - 2 and the maximum usual value + 2. Round your answer to the nearest hundredth unless otherwise noted. n = 1042, p = 0.80 2) Use...

The shearing mechanism is used to quickly cut long sections of extruded plastic into 1-inch pieces. In order to make a nice smooth cut, the motor must turn the crank at 300 rpm. At the instant shown,...

SOlve x (number ? defective) P(x) A new device is assembled from five O 0.50 independent parts. The probability that one or 1 0.20 more of the parts are defective is provided in the 2 0.15 table. If...

3. Consider the design data for an axial compressor nestled on machine foundation as shown below. Rocking Design data: Static weight of machinery: 20 tons Rotational speed: 327 rpm Soil density: 18...

A foundation for well - adjusted single acting drop hammer is situated on a compacted sand deposit. Details of machine foundation and soil are given below Weight of tup = 2 0 k N ; Height of fall of...

Design the foundation of diesel-generator set complete with specifications using the following data: Note: KVA = 1,000 P.F. = 0.80 Cylinders, V = 16 = Weight 10,297 kg Bedplate dimensions = 2,500 mm...

Find the natural frequency of the system shown in Fig. 2.54. Figure 2.54:- Rotating machine B Isolator (Helical springs) FIGURE 2.54 Isolated rotating machine. Foundation block

Where is the top of the concrete elevation of the machine foundation

118 CHAPTER 5 THE ERINDALE HOSPITAL FOUNDATION You are a CA and work for Wilson Chartered Accountants. You are in the process of conducting the year-end financial statement audit for the Erindale...