Question: A solid steel bar is attached to supports through a steel pin ( d 2 = 3 0 m m ) . The thickness of

A solid steel bar is attached to supports through a steel pin (d2=30mm). The thickness of the supports is t=20mm. The diameter of the steel bar. (d1) is 60 mm . The load applied P is 170 kN . Calculate the bearing stress between the support and the steel pin MPa.
Answered
ect Answer
141.6667 margin of error +-0.1
A solid steel bar is attached to supports through

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A solid steel bar of diameter d1 = 60 mm has a hole of diameter d2 = 32 mm drilled through it (see figure). A steel pin of diameter d2 passes through the hole and is attached to supports. Determine...

Q:

2.94 The elastic strip with a cutout is of length L, width b, and thickness t. Derive the expression for the elongation of the strip caused by the axial load P. 2.95 The aluminum bar of...

Q:

DAN ANALYSIS WEEN MANALYSIS 5-15 Problem 5-15 ANALYSIS. 5-16 Problem 5-16 5-17 Problem 5-17 A rectangular steel bar supports the two overhanging loads shown in the figure. Using superposi- tion, find...

Q:

6. A garage floor is sloped _" per foot for proper drainage. A. 1/8" to 1/4 B. 1/4" to 3/4 C. 3/4" to 1 . 4 7. Control joints should be provided at a maximum of _" intervals in both directions on a...

Q:

A 4 5 - mm - diameter solid steel shaft supports loads P A = 1 . 8 k N and P C = 3 . 1 k N as shown. Assume that L 1 = 1 2 5 m m , L 2 = 2 6 0 m m , and L 3 = 1 9 0 m m . The bearing at B can be...

Q:

Taque To is appled at he midrint of a soled sted bar with Mameter de 13 and length 15L which 1s thuckness ty and lenath oes L. The twist t c is specefod bonded to two Grass collars, each wnth wall IS...

Q:

The figure illustrates a number of beam sections. Use an allowable bending stress of 1.2 kpsi for wood and 12 kpsi for steel and find the maximum safe uniformly distributed load that each beam can...

Q:

Produce a work breakdown structure for the minor dwelling project plan ( the image files provided) using ms word or another software. The work breakdown structure should have 4 hierarchy levels with...

Q:

in Fig. The diameters 1. An som An som long steel made of middle and the last segments of the bar are 30 mm, 25 mm and 30 mm respectively. Also, find the elongation of the bar. E = 200 GPa 200 kN P...

Q:

Summarize this for me. Someone who understand the HEA and MEA perfectly and also the summary should be 2 or over 2 pages. Someone who understands this perfectly A scrap-tolerant alloying concept...

Q:

What does this MIS class do differently than other classes? Maybe the assignments are a bit different, maybe the instructor does some things a little differently. What if a university instructional...

Q:

what is the per share value of common stock based on: non-operating assets: $1,500,000 debt: $7,000,000 cost of capital: 12% common stock outstanding: 175,000 projected free cash flows: year 1:...

Q:

Factors ) for identifying a tax haven is ( are ) 1 . No or low taxes on income 2 . Lack of effective exchange of information 3 . Lack of transparency 4 . No substantial activities

Q:

What is your planDescribe your action plan (8 actions minimum) for the Marketing Mix Elements in the Introduction stage and in the growth stage of your restaurant life cycle by completing the table...