Question: A square bar used as a mechanical link in an automated packaging machine is subjected to a tensile force F. The force, dimensions and material

A square bar used as a mechanical link in an automated packaging machine is subjected to a tensile force F.

The force, dimensions and material are listed below. All answers are in SAE units.

Force (F) = 125,500 lbf

Length (L) = 13.12 ft

Side (b) = 1.25 inch

Material = 316L Austenitic Stainless Steel

Temper = Half Hard

Determine the beam stress when it is loaded in tension with force F. Round your answer to the nearest whole number. Provide your answer in lbf/in2.

Determine the Factor of Safety (FOS) of the determined stress compared to yield strength. Round your answer to the nearest one decimal place.

Step by Step Solution

★★★★★

3.45 Rating (148 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

To determine the beam stress when the square bar is loaded in tension with force F we can use ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Problem 1 At December 31, 2025, Arnold Corporation reported the following plant assets: Land Buildings Less: Accumulated depreciation - buildings Equipment Less: Accumulated depreciation - equipment...

Q:

Managing Scope Changes Case Study Scope changes on a project can occur regardless of how well the project is planned or executed. Scope changes can be the result of something that was omitted during...

Q:

A tube used for medical procedures has an outside diameter and an inside diameter The torque, dimensions and material are listed below. All answers are in SI units. Torque (T) = 1,975 Nm Out Dia....

Q:

A square bar used as a mechanical link in an automated packaging machine is subjected to a tensile force F. Determine the beam stress when it is loaded in tension with force F. Determine the Factor...

Q:

Provide a real-world example of MNCs that have faced significant challenges due to discrepancies in accounting standards across countries? How did they overcome these challenges, or did they?

Q:

A tensile member in a machine structure Torsion Compute the torsional shear stress in a circular shaft with a diameter of 5 0 mm that is subjected to a torque of 8 0 0 N - m . Compute the torsional...

Q:

\f\f\fChapter 2 Service Strategy Learning Objectives After completing this chapter, you should be able to: 1. Formulate a strategic service vision. 2. Describe how a service competes using the three...

Q:

Read the following article and summarize of the article. ETHICS CONDUCT INTEGRITY HONESTY TRUST Acting on our By 1944, IBM built computers for Ethics the Manhattan Project with mechanical relays that...

Q:

Finance assignment P12 A B H K L M N D G Financial Management - Contributory Income Statements 2 1. Joe's Bistro has three sales revenue departments with direct costs and the average monthly figures...

Q:

Mechanical Systems 2 For each material below, find S u t and S y . Then indicate which of the materials shown below would you choose to obtain: a . maximum stiffness ( find E for each material ) , b...

Q:

Chapter 7 Assignment 4 ADDING MORE INFORMATION: DRONE CITY Restore the file Drone City Ch 07 (Backup) that you downloaded from the student companion site, and then add the following transactions....

Q:

If F = 200 N, determine the required angle ? so that the resultant couple moment is zero. 300 N 300 mm 15 307 300 N

Q:

Jiao, a student of business management, claims that the shareholder primacy model is better than the stakeholder model of business management. Which of the following statements best supports her...

Q:

Cold water (cp = 4.18 kJ/kg ¢ °C) leading to a shower enters a well-insulated, thin-walled, double-pipe, counter-flow heat exchanger at 15°C at a rate of 0.25 kg/s and is heated to...

Q:

Castellitto Company sells automatic can openers under a 75-day warranty for defective merchandise. Based on past experience, Castellitto estimates that 3% of the units sold will become defective...

Q:

Helium gas is compressed from 14 psia and 70F to 120 psia at a rate of 5 ft3/s. Determine the power input to the compressor, assuming the compression process to be (a) Isentropic, (b) Polytropic with...

Q:

Comprehensive problem with ABC costing. Pet Transport Company makes two pet carriers, the Cat-allac and the Dog-eriffic. They are both made of plastic with metal doors, but the Cat-allac is smaller....

Q:

Why do public utility companies usually have capital structures that are different from those of retail firms?

Q:

Knowledge management takes explicit knowledge, transforms it, and then stores it as tacit knowledge. Group of answer choices True False

Q:

Compare the eutectic temperatures of a Fe-4.3% C cast iron with a Fe-3.6% C- 2.1% Si alloy. Which alloy is expected to be more machinable and why?

Q:

The density of BCC iron is 7.882 g/cm3, and the lattice parameter is 0.2866 nm when hydrogen atoms are introduced at interstitial positions. Calculate (a) The atomic fraction of hydrogen atoms; and...

Q:

A sample of cubic SiC was analyzed using XRD. It was found that the (111) peak was located at a 2 of 16. The wavelength () of the x-ray radiation used in this experiment was 0.6975 . Determine the...

Q:

=+What factors do you think played a role in your gender development?

Q:

=+1. Ask your parents about your gender-related behavior as a child and about their views on how their parenting influenced your gender development. Do their recollections ring true with your...

Q:

=+1. What three principles must not be violated for a variation in sexual behavior to be considered harmless?