Question: A statically indeterminate beam shown in the figure below, rests on roller support at B and a fixed support at A . The flexural rigidity

A statically indeterminate beam shown in the figure below, rests on roller support at B and a fixed support at
A. The flexural rigidity of the beam is constant and of value El. Length of the beam is 5m. Beam is subjected
to a distributed load which varies linearly, from maximum 8kNm at point A to 0 at point B.
Problems:
Determine reaction forces and moments at the supports A and B.
Determine the deflection curve.
Sketch the bending moment diagram.
Sketch the shear force diagram.
Determine the point of contraflexure (the point where bending moment is 0).
A statically indeterminate beam shown in the

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

For the hexadecimal main memory addresses 111111, 666666,BBBBBB, show the following information, in hexadecimal format: a. Tag, Line, and Word values for a direct-mapped cache, using the format of...

Q:

A statically indeterminate beam of length L = 8 m is fixed supported at both ends and is subjected to the uniform loading w = 5 k N m applied over half of the beam, as shown in the figure below. The...

Q:

5 . Using Castigliano's method, find the slope at the mid - length C of a straight, beam due to the applied moment Mo , as shown. ( a ) Write a FBD showing all the support reactions, ( b ) Show that...

Q:

Q 2 . A continuous beam structure as shown in Figure Q 2 subjected to uniform distributed load of 6 k N m and point load of 3 0 k N . The beam is supported by a fixed support at A and roller supports...

Q:

Question 2 A statically indeterminate beam is loaded with uniformly distributed load from A to C and concentrated load at joints B , D , and D as illustrated in Figure Q 2 . The total length of the...

Q:

MUST use the Force Method, and determine the reaction at A and B in the statically indeterminate beam. Note B is a fixed support and A is a roller support. Use Appendix if appropriate. The beam...

Q:

(a) (b) A (i) (ii) Explain the difference between a statically determinate and statically indeterminate beam. 1 m A cantilever beam of length of 5.0 m carries a uniformly distributed load of 15 kN/m,...

Q:

3 . \ ( ( 5 0 \ % ) \ ) Consider a cantilever beam with constant \ ( E I \ ) and an additional spring support at the free end, as shown in Figure 3 . Neglect shear effect. ( a ) Analyze statical...

Q:

Problem # 1 : ( 7 0 points ) The beam ABC of length 2 L is fixed ( i . e . clamped ) at point A and supported by a roller at B , as shown in Figure 1 ( on the following page ) . The beam is loaded by...

Q:

Problem \ # 1 : ( 7 0 points ) The beam \ ( A B C \ ) of length \ ( 2 L \ ) is fixed ( i . e . clamped ) at point \ ( A \ ) and supported by a roller at \ ( B \ ) , as shown in Figure 1 ( on the...

Q:

I need a solution to this question For the system shown in the figure, determine, by the method of consistent deformations, the reaction at support e. The flexibility of the spring f = 0.2 cm/kN of...

Q:

Consider the following information Kilogram 80,000 WIP, May 1 Started into production during May WIP, May 31 Cost added during May 400,000 30,000 Percent Completed Material Conversion 20% 80% 60% 30%...

Q:

Foley Corporation has seven operating segments with total revenues as follows (in 000,000). Based only on the revenues test, which operating segments arereportable? KonamiY600 KSC Penley 650 250 275...

Q:

A real estate broker has a legal obligation to the a . party who is paying him or her. b . lender. c . buyer. d . seller.

Q:

Expenditures 1. Excavation costs for new building $13,540 2. Architect's fees on building plans 39,540 3. Full payment to building contractor 655,600 4. Cost of real estate purchased as a plant site...