Question: Additional Algo 9 - 1 Process Capability Index A drilling process has an upper specification of 1 . 7 5 1 millimeters and a lower

Additional Algo 9-1 Process Capability Index
A drilling process has an upper specification of 1.751 millimeters and a lower specification of 1.649 millimeters. A sample of parts had a mean of 1.7 millimeters with a standard deviaiton of 0.027 millimeters.
What is the process capability index for this system?
Note: Round your answer to 4 decimal places.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Q:

please answer both! QUESTION 1 2.5 points Save Answer Process capability index Cpx - Minimum of Lower specification Upper specification - 30 30 Process capability ratio: Upper specification - Lower...

Q:

You can manufacture a bolt with one of 6 different processes. The specifications require that the bolt be between 2.04 cm and 2.08 cm long. Six candidate processes and the standard deviations of...

Q:

What is the maximum hourly output from a process with four stepshaving outputs of 20 units/hour, 25 units/hour, 30 units/hour and15 units/hour? 20,25,30, or 15 Which error type indicates null...

Q:

help please! Additional Algo 9-2 Process Capability Index 6 A weighing process has an upper specification of 1.841 grams and a lower specification of 1.699 grams. A sample of parts had a mean of 1.77...

Q:

A manufacturer wants to buy a new machine for his assembly line. there are two alternatives, Machine A and Machine B . The decision will be made based on the process capability ratio Cp . Machine A...

Q:

True/False 1. A worker moving inventory from one machine to another is considered non-value-added work 2. A new backpack that has a zipper which is broken due to a supplier problem is indicative of a...

Q:

True/False 1. A worker moving inventory from one machine to another is considered non-value-added work 2. A new backpack that has a zipper which is broken due to a supplier problem is indicative of a...

Q:

A quality engineer is comparing five different processes used to manufacture the same product. All five processes have the same process capability index ( Cpl ) , and the specification limits are...

Q:

Question 17 (1 point) Calculate Cpk (process capability index) from the following information. Upper specification limit 0.55 Lower specification limit 0.023 Mean 0.036 Standard deviation 0.05 Note:...

Q:

Table 1 : Resistance Values ( in Ohms ) of Resistors from Assembly Line Sample No . Resistance 1 Resistance 2 Resistance 3 Resistance 4 Resistance 5 Resistance 6 1 9 9 . 8 1 0 0 . 2 1 0 0 . 5 1 0 0 ....

Q:

Lemington Enterprises is considering a project to replace its fleet of 10 vehicles. The company makes a fleet replacement decision every five years. Its current fleet of 10 vehicles was purchased...

Q:

A closely wound solenoid of 800 turns and area of cross section 2.5 104 m carries a current of 3.0 A. Explain the sense in which the solenoid acts like a bar magnet. What is its associated magnetic...

Q:

Roy's father gives him a capital inherest in the Famly Partnership. Discuss whether the Sec. 7 0 4 ( e ) family partreruhip rules apply to this interest. A . The Sec. 7 0 4 ( e ) nules apply because...

Q:

The annual demand for an item is 1,700 units. The order cost is $7. Unit cost is $8 and the unit holding cost per year is 18% of the item's value. The order quantity is 125 units. What are the total...