Question: At a point on the surface of a cylinder, the material is subjected to shear and normal stresses as shown on the stress element below.

At a point on the surface of a cylinder, the material is subjected to shear and normal stresses as shown on the stress element below. Using Mohr’s circle, determine the stresses acting on an element inclined at an angle θ = 40.

Step by Step Solution

★★★★★

3.55 Rating (152 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

100 MPa 28 for xface face 34 5040 34 MPa Z Cry x 100MPa z 28 MPa 34 MPa ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

At a point on the surface of a machine component, the stresses acting on the x face of a stress element are (x = 5900 psi and Txy = 1950 psi (see figure). What is the allowable range of values for...

At a point on the surface of a machine component the stresses acting on the x face of a stress element are (x = 42 MPa and Txy = 33 MPa (see figure). What is the allowable range of values for the...

At a point on the surface of a machine the material is in biaxial stress with (x = 3600 psi, and (y = - 1600 psi, as shown in the first part of the figure. The second part of the figure shows an...

The yield stress for a zirconium-magnesium alloy is Y = 15.3 ksi. If a machine part is made of this material and a critical point in the material is subjected to in-plane principal stresses 1 and ...

Solve Prob. 1061 using the maximum distortion energy theory Data from Problem: 10-61. The yield stress for a zirconium-magnesium alloy is Y = 15.3 ksi. If a machine part is made of this material and...

Solve Prob. 1063 using the maximum distortion energy theory. Problem: 10-63 If a machine part is made of tool L2 steel and a critical point in the material is subjected to in-plane principal stresses...

Using Mohrs circle, determine the principal moments of inertia for the triangular area and the orientation of the principal axes of inertia having an origin at point O. Given: a = 30 mm b = 40 mm a

An element on the surface of a drive shaft is in pure shear and is subjected to stresses xy = 2700 psi, as shown in the figure. Using Mohrs circle, determine the following. (a) The stresses acting...

Using Mohrs circle, determine for the quarter ellipse of Problem 9.67 the moments of inertia and the product of inertia with respect to new axes obtained by rotating the x and y axes about O (a)...

Using Mohrs circle, determine the moments of inertia and the product of inertia of the area of Problem 9.73 with respect to new centroidal axes obtained by rotating the x and y axes through 30 o...

QUESTION 4 ( 2 0 Marks ) REQUIRED Use the information provided below to calculate the following ( expressed to two decimal places ) : 4 . 1 Cost of equity using the Capital Asset Pricing Model ( 4...

a). The following information was extracted from the stores ledger of Alpha Limited during the month of March 2022 Opening inventory 4000 units valued at shs. 160,000 Receipts March 5 5,000 units @...

What values can be held related to leadership and what informs them?

iid Estimating variance for normal data. Suppose that we observe data X1, ..., Xn N(0, v) we know the mean is 0, but we don't know the variance v. (We are writing variance = v, instead of , to make...

Four small spheres, each of which you can regard as a point of mass 0.200 kg, are arranged in a square 0.400 m on a side and connected by light rods a)Find the moment of inertia of the system about...

In the class, we leamt the capital recovery factor (CRF) that is given as i(1+i)n (1+i)n - 1 where i the interest rate and n is the number of annuities received. CRF 4a) (10pts) Given i, find the...

Apex Properties, Inc. owns two warehouse buildings that it rents to other businesses. The two buildings are very desirable properties and this enables Apex to require that renters pay rent in...

a. Show that the expansion of q(x) in ascending powers of x can be approximated to 10 2x + Bx 2 + Cx 3 where B and C are constants to be found. b. Find the percentage error made in using the series...

The 10-kg square plate shown is supported by three vertical wires. Determine (a) The tension in each wire when a = 100 mm, (b) The value of a for which tensions in the three wires are equal. 300 mm

The base of a dam for a lake is designed to resist up to 150 percent of the horizontal force of the water. After construction, it is found that silt (which is equivalent to a liquid of density =...

A load of weight 400 N is suspended from a spring and two cords which are attached to blocks of weights 3W and W as shown. Knowing that the constant of the spring is 800 N/m, determine (a) The value...

What are the nontax advantages and disadvantages of defined benefit plans relative to defined contribution plans?

In 2014, Nitai contributes 10 percent of his $100,000 annual salary to a Roth 401(k) account sponsored by his employer, AY, Inc. AY, Inc., matches employee contributions dollar for dollar up to 10...

Kim has worked for one employer her entire career. While she was working, she participated in the employer's defined contribution plan [traditional 401(k)]. At the end of 2014, Kim retires and the...