Question: CCNA - 2 v 7 . 0 Case Study ( Rev B ) Static Routes, VLANs, Switch Security, DHCP , Wireless, Spanning - Tree PHASE

CCNA-2v7.0 Case Study (Rev B) Static Routes, VLANs, Switch Security, DHCP, Wireless, Spanning-Tree PHASE I IP Addressing and VLANS The Carl I. Samson Company (C.I.S. Co) of Bangor, Maine has recently acquired Big-Corp with offices in Phoenix, AZ and Chicago, IL. Until a final decision is made, static routing and both IPv4 and IPv6 addressing will be used. Your job is to configure all Routers, Switches and PCs to support the newly formed network. Subnet Address Subnet Mask/Prefix Len # of Hosts Network Assignment VLAN # Name Phoenix 172.25.64.0/23255.255.254.0512 Summary 172.25.64.0/24255.255.255.0150 PHX-LAN-110110 PHX-LAN-110172.25.65.0/25255.255.255.12875 PHX-LAN-120120 PHX-LAN-120172.25.65.128/27255.255.255.22425 PHX-WIFI-LAN n/a 172.25.65.160/29255.255.255.2484 PHX-MGMT 100 PHX-MGMT 172.25.65.168/30255.255.255.2522 PHX-WIFI-LINK WIFI-LINK 172.25.65.172/30255.255.255.2522 PHX-LOOPBACK n/a Chicago 172.25.66.0/24255.255.255.0256 Summary 172.25.66.0/25255.255.255.12890 CHG-LAN-210 n/a 172.25.66.128/28255.255.255.24010 CHG-LAN-220 n/a 172.25.66.144/30255.255.255.2522 CHG-LOOPBACK n/a Bangor 2001:C47:F8A5/48 Global Prefix Subnet 300/64 n/a BAN-LOOPBACK n/a Subnet 310/64 n/a BAN-LAN-310310 BAN-LAN-310 Subnet 320/64 n/a BAN-LAN-320320 BAN-LAN-320 Subnet F /64 n/a BAN to BRDR n/a WAN Links 192.168.8.48/28255.255.255.24016 Summary 192.168.8.48/30255.255.255.2522 PHX to BRDR n/a 192.168.8.52/30255.255.255.2522 PHX to CHG n/a 192.168.8.56/30255.255.255.2522 CHG to BRDR n/a 192.168.8.60/30255.255.255.2522 BRDR-LOOPBACK n/a PHASE II - Router Configuration The following table outlines the configuration tasks you need to perform on the routers and Layer-3 switch In the topology. Where specific configurations are required, they are noted below; otherwise it is your discretion which names, descriptions, banners, and/or addresses you will use (Y means yes configure it). Configuration Chicago Router Phoenix SW-1 Bangor Router Border Router Device name CHG-RTR PHX-SW-1 BAN-RTR BRDR-RTR Basic configuration settings on all Routers, Save the running configuration file Hostname, encrypt all passwords, Enable Secret = class, Disable IP domain lookup, Banner = Any text, Console & VTY: password cisco, Logging synch, no timeout Enable Routing n/a ip routing Ipv6 unicast- routing Ipv6 unicast- routing Disable login for 1 min if 3 failures in 60 seconds Y Y Y Y Create a username of guest with password cisco n/a Y n/a n/a Set the Domain name to cisco.com n/a Y n/a n/a Create a crypto key of 1024 bits n/a Y n/a n/a Configure SSH ver 2 n/a Y n/a n/a Configure all interfaces, SVIs, and sub-interfaces (as appropriate) using the information provided above and in the network diagram with the following:-Description-IP address (1st usable address is default gateway)-Subnet mask or prefix length-Encapsulation and VLAN assignment-IPv6 Link-Local address (BRDR-RTR ::1, BAN-RTR ::2) Y G1/0/22 G1/0/23 G1/0/24 are layer-3 interfaces Use VLAN 77 as the native VLAN in Router-on-a- Stick Y Configure a Loopback-1 Interface with proper IP address Y Y Y Y Disable CDP globally Y Y Y Y Static default route for IPv6 towards ISP n/a n/a n/a Fully Specified Static route for 2001:C47:F8A5:300/64 to BAN-RTR n/a n/a n/a Fully Specified Static route for 2001:C47:F8A5:310/64 to BAN-RTR n/a n/a n/a Fully Specified Static route for 2001:C47:F8A5:320/64 to BAN-RTR n/a n/a n/a Fully Specified Static default route for IPv6 towards BRDR-RTR n/a n/a Fully Specified n/a Static default route for IPv4 towards ISP n/a n/a n/a Exit Interface Static route for PHX-Summary to PHX-SW-1 n/a n/a n/a Exit Interface Static route for CHG-Summary to CHG-RTR n/a n/a n/a Exit Interface Static route for WAN-Summary to PHX-SW-1 n/a n/a n/a Exit Interface Static default route for IPv4 towards BRDR-RTR Exit Interface n/a n/a n/a Static route for PHX-Summary to PHX-SW-1 Exit Interface n/a n/a n/a Static route for WAN-Summary to PHX-SW-1 Exit Interface n/a n/a n/a Static default route for IPv4 towards BRDR-RTR n/a Exit Interface n/a n/a Static route for CHG-Summary to CHG-RTR n/a Ex

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Programming Questions!