Question: compression force in two end posts The pin of a rocker bearing in a bridge is designed for a) bearing and shear b) bending and

compression force in two end posts The pin of a rocker bearing in a bridge is designed for

a) bearing and shear

b) bending and shear

c) bearing and bending

d) bearing, shear and bending

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

1. In Step 1 enter all the following starting criteria: Concrete unit weight = 150 pcf 1) 2) 3) 4) 5) 6) 7) Cement Type I No retarder but with 25% fly ash (no slag). Concrete rate of pour, R = 6.654...

Q:

Part2A, 2B, and Discussion I'll need answers, formulas, and work shown please. Part 2A Torsional Key Design Choose a key material from Table 02 above and document your choice of material and temper...

Q:

1. Choose a key material from Table 02 above and document your choice of material and temper in your work. I used Tin Brass (Sy= 55000posi, Su=6000 ksi, E=16000, elongation: 6%) Hardness 76) 2....

Q:

A free-piston engine under development consists of a small piston in a cylinder. Each end of the cylinder behaves like a two-stroke engine, in which the following sequence of processes occurs...

Q:

You must modify this code so that it works for any truss that the user wishes to analyze, whether 2-D or 3-D. Therefore, after your code is modified, all trusses should be assumed as 3-D Space...

Q:

. D . A primary horizontal me mbe rof length 4 . 0 m in a roof truss in Southe m Australia is to che cke dfor combined actions ( Compressior - Tension and Bending ) . Afterthe analysis of the...

Q:

Can I get the number in calculation, the result: Method 1 : Using Load Moment and Torso Moment to calculate Muscle Reaction Force. Estimate low back compression by combining Load Weight, Torso Weight...

Q:

Which of the following statements is incorrect? [ a ] The first internal combustion engines used in automobiles were used as fuel. They used air - gas at atmospheric pressure. [ b ] Otto proposed an...

Q:

PLEASE DO ALL 3 This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.7m wide and 3.6m high. If the force at the end of the arm is F=110.0N, what is the force...

Q:

Figure P3 Ho 4 m P B I 4 m F J 4 m b) Calculate the vertical reaction at support A. [0 mark] Provide your answer in units of kN to 4 decimal places. Indicate a horizontal force pointing left as being...

Q:

For the following hypothesis, test: with n = 15, s = 7.5, and = 62.2, state a. The decision rule in terms of the critical value of the test statistic b. The calculated value of the test statistic c....

Q:

Employ the multiple-application Simpsons rule to evaluate the vertical distance traveled by a rocket if the vertical velocity is given by = 11 t 2 5 t 0 t 10 = 1100 5 t 10 t 20 = 50 t + 2( t...

Q:

View Policies Current Attempt in Progress Which of the following is a characteristic of a perpetual inventory system? Cost of goods sold is recorded with each sale. Cost of goods sold is determined...

Q:

10 1 Fixed manufacturing overhead (MOH) volume variance is a measure of utilization of plant facilities during the period and is calculated as follows: Predetermined overhead rate x (Denominator...