Consider the circuit shown in $($Figure $1).$

Figure$1$ of $1$

The figure shows a single$-$loop electric circuit that consists of$,$ counting clockwise, an AC voltage source, a $100-$ohm resistor, a $0\mathrm{.}5-$henry inductance and another AC voltage source. The equation of voltage v$1$ of t on the first source is $100$ sine left$-$bracket $100$ t right$-$bracket, with the positive reference taken clockwise. The equation of voltage v$2$ of t on the first source is $100$ cosine left$-$bracket $100$ t plus $30$ degrees right$-$bracket, with the positive reference taken counterclockwise. The voltages on the resistor and the inductance are labeled as v subscript R and v subscript L respectively, with the positive reference taken counterclockwise. Current i of t flowing through the circuit is measured clockwise.

Part A

Part complete

Find the phasor V$1$

$.$

Enter your answer using polar notation. Express argument in degrees.

V$1$

$=$

$100\backslash$angle $90$

Previous Answers

Correct

Part B

Part complete

Find the phasor V$2$

$.$

Enter your answer using polar notation. Express argument in degrees.

V$2$

$=$

$100\backslash$angle $30$

Previous Answers

Correct

Part C

Find the phasor VR

$.$

Enter your answer using polar notation. Express argument in degrees.

Activate to select the appropriates symbol from the following choices. Operate up and down arrow for selection and press enter to choose the input value type

VR

$=$

Previous AnswersRequest Answer

Incorrect; Try Again; $7$ attempts remaining

Part D

Find the phasor VL

$.$

Enter your answer using polar notation. Express argument in degrees.

Activate to select the appropriates symbol from the following choices. Operate up and down arrow for selection and press enter to choose the input value type

VL

$=$

Previous AnswersRequest Answer

Incorrect; Try Again; $12$ attempts remaining

Part E

Find the phasor I

$.$

Enter your answer using polar notation. Express argument in degrees.

Activate to select the appropriates symbol from the following choices. Operate up and down arrow for selection and press enter to choose the input value type

I

$=$

nothing

Request Answer

Part F

Draw the phasor diagram.

The location and orientation of the vectors will be graded. The length of the vectors will not be graded.

Select the elements from the list and add them to the canvas setting the appropriate attributes.Select to observe the list of the elements that can be added to the canvas. Press CTRL$+$Y to get to the elements on the canvas. Press CTRL$+$Q to quit the application.

Select to show$/$hide the vector for the sum of the drawn vectors. Press CTRL$+$Y to get to the elements on the canvas. Press CTRL$+$Q to quit the application.

Delete the selected element. Press CTRL$+$Y to get to the elements on the canvas. Press CTRL$+$Q to quit the application.

Press to go to keyboard navigation instructions below the canvas.

Select to remove all drawn elements. Press CTRL$+$Y to get to the elements on the canvas. Press CTRL$+$Q to quit the application.

Attributes panel is empty. Press CTRL$+$Y to get to the elements on the canvas. Press CTRL$+$M to return to the main menu. Press CTRL$+$Q to quit the application.No elements selected

Select the elements from the list and add them to the canvas setting the appropriate attributes. Press CTRL$+$M to get to the main menu.Select the elements from the list and add them to the canvas setting the appropriate attributes. Press TAB to get to the main menu.Use arrow keys to apply parallel transition to the object. Press TAB to move to the next element on the canvas. Press SHIFT$+$TAB to return to selecting the end point. Press DEL to delete the element from the canvas. Press CTRL$+$A to modify the attributes. Press CTRL$+$M to get to the main menu. Press ESC to quit adding or editing this element. Press CTRL$+$Q to quit the application.Press SPACE to get to the set of hotspots or use arrow keys to move on the canvas. Press ESC to quit adding or editing this element. Press CTRL$+$A to modify the attributes. Press CTRL$+$M to get to the main menu. Press CTRL$+$Q to quit the application.Press SPACE to get to the set of hotspots or use arrow keys to move on the canvas. Press TAB to select the whole element. Press SHIFT$+$TAB to move to selecting the start point. Press CTRL$+$A to modify the attributes. Press CTRL$+$M to get to the main menu. Press ESC to quit adding or editing this element. Press CTRL$+$Q to quit the application.Press TAB to move to the next element on the canvas. Press DEL to delete the element from the canvas. Press CTRL$+$A to modify the attributes. Press CTRL$+$M to get to the main menu. Press ESC to quit adding or editing this element. Press CTRL$+$Q to quit the application.Press SPACE to get to the set of hotspots or use arrow keys to move on the canvas. Press ENTER to change the direction. Press TAB to move to the next element on the canvas. Press DEL to delete the element from the canvas. Press CTRL$+$A to modify the attributes. Press CTRL$+$M to get to the main menu. Press ESC to quit adding or editing this element. Press CTR