Question: Design a 4-bit synchronous left-shift register using D flip-flops (7474). Your shift register should have an asynchronous parallel load, serial in, serial out, and parallel

Design a 4-bit synchronous left-shift register using D flip-flops (7474). Your shift register should have an asynchronous parallel load, serial in, serial out, and parallel out bus. You may convert a flip-flop of another type into a D flip-flop, if needed. Answer the following questions in the report: 1. How would you modify this design to provide synchronous parallel load instead of asynchronous parallel load? 2. How would you modify this design to allow a synchronous right-shift along with synchronous parallel load?

Bonus if you can provide a breadboard or logism example.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

1 . You only have D - Flip Flops with asynchronous preset and reset. ( 1 ) Design 2 - Bit shift register with synchronous parallel load using D FlipFlops. ( 2 ) . Design 2 - Bit shift register with...

exam! please help!! Consider the universal shift register with an Asynchronous parallel load shown in the following figure: Q- Q. Q: Q: Q: Q: Q, Qo SI Reset Left: Right L'S Clock 8-bit Shill Register...

The Serial - In Serial - Out ( SISO ) shift register is a circuit that accepts serial data on its input pin and shifts it out serially on its output pin. The 4 - bit SISO consists of four D flip -...

Problems: 6.35(e,f) 368 Chapter 6 Registers and Counters Problems 369 PROBLEMS S1 So Register Operation No change Complement the four outputs Clear register to 0 (synchro- nous with the clock) Load...

help for all questions Ch5: Sequential Circuits A- Latches and Flip-Flops 1- Latches are A. Edge sensitive. B. Both edge and level sensitive. C. Level sensitive. D. None of the previous 2- Flip-Flops...

Write a Verilog description using behavioral modeling for: (a) The positive edge-triggered JK Flip-Flop of Figure 5.9. (b) A D flip-flop with a synchronous reset input and a positive edge triggered...

Just need the deliverables!! 1 Introduction Write and verify an HDL model of a serial adder-subtractor circuit. Recall that serial addition of two binary numbers can be implemented using shift...

Using Quartus design and test an 8-bit Right shift register with serial input... Part II Modify the circuit to use the SET FF to set the register to 1010 0111 with a single input. Once set modify the...

Please answer table 18-3 and 18-4, and draw the logic diagram. Thank you. d) Changing the MOD-number of a counter: In the preceding step, you investigated a three-bit counter. You determined its...

Access the Disability Standards for Education 2005 and summarise how the requirements would apply to the role of an Education Support Worker (ESW). Legal and Ethical Requirements Application to the...

AMG Enterprises is interested in investing in a scale-expanding project. It spent $1 billion last year doing research about this project and has found out the following. -The project will require a...

A company just paid a $ 3 . 5 0 annual dividend per share to its common shareholders. Future dividends are expected to grow at a rate of 1 2 % for each of the next 4 years, and then at a constant...

Compared with half a century ago, adoption has become _ _ _ _ _ _ _ _ _ common, but it is more open and acceptabl e , so we probably discuss it _ _ _ _ _ _ _ . fill in the blanks more or much less or...

KEY QUESTION In long-run equilibrium, P minimum ATC MC. Of what significance for economic efficiency is the equality of P and minimum ATC? The equality of P and MC? Distinguish between productive...

KEY QUESTION Complete the following table by calculating marginal product and average product from the data given: Plot the total, marginal, and average products and explain in detail the...

KEY QUESTION A firm has fixed costs of $60 and variable costs as indicated in the table on the next page. Complete the table and check your calculations by referring to question 4 at the end of...