Question: Explain why most lasers need to be connected to a DC power supply?

Explain why most lasers need to be connected to a DC power supply?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Physics Questions!

Q:

Question 24 A 11 V battery is connected across two resistors in series. If the resistors have resistances of 818 $2 and 590 & what is the voltage drop Not complete across the 590 0 resistor. 4SD Zero...

Q:

452 129 2A + Points: 4 21) A 4.0-Q resistor is connected in parallel with a 12-Q resistor and both of these are connected to a DC power supply with voltage Vas shown in Figure 21-9. If the total...

Q:

read experiment attached Q: Using the Table of Standard Reduction Potentials, calculate the standard cell voltage, E, for each of the cells tested. Compare the observed and calculated values. How can...

Q:

b) A 30.0mH inductor is connected to a DC power supply. The power supply's emf is fixed at 10.0V. i. If you turn down the power supply's current at a constant rate, dI/dt=50.0A/s, Calculate the...

Q:

R, =10 Q WW 1A R3=5 0 R, =10 0 Three resistors are connected to a DC power supply as shown in the figure, What is the voltage of the source that would produce a current or 1A though R17

Q:

PHYS 1322 - Summer ZOZI Final Exam (take-home) Your Name EXTRA CREDIT An RC circuit connected to a DC power supply has a 300 Q resistor, a 25 mF capacitor, and a 15 V battery. How much time must pass...

Q:

EXTRA CREDIT An RC circuit connected to a DC power supply has a 300 0 resistor, a 25 mF capacitor, and a 15 V battery. How much time must pass for the current to reach 55 mA? Fcult

Q:

MW Light bulbs in series connection Note: The symbol represents a light bulb which can be treated as a resistor. ' 4' 0'4 V DMM Vs DMM 5 Figure 4(a) One bulb "1 the c1rcu1t Figure 4(b) Two bulbs in...

Q:

can anyone do that please ? EL-100 LAB #2 CHOD Measuring DC Current, Voltage, and Resistance OBJECTIVE: To become proficient in the construction of simple circuits on the ET 3600 Trainer and...

Q:

Exp.: 3 / RMS value of an AC waveform Objective: To investigate ac waveforms and the power carried by them. Introduction: At times ti, ta, ts, and ta, the power will be iz R, ZR,R, and i 3R Watts...

Q:

Widgets are provided by a competitive constant-cost industry where each firm has fixed costs of $30. The following chart shows the industry-wide demand curve and the marginal cost curve of a typical...

Q:

The members of the structure in Fig. P-120 weigh 200 lb/ft. Determine the smallest diameter pin that can be used at A if the shearing stress is limited to 5000 psi. Assume single shear. Figure P-120

Q:

6 Write the decimal numbers in each set in order of size, starting with the smallest. 45.454, 45.545, 45.399, 45.933 a b 5.183, 5.077, 5.044, 5.009 31.425, 31.148, 31.41, 31.14 c 7.502, 7.052, 7.02,...

Q:

Find all solutions to the equation. sec+2=0 Write your answer in radians in terms of it, and use the "or" button as necessary. Example: 0 = 5 +2k, k = Z or 0 = 7+k, kl Help with this notation = 0 0...