Question: Given open-loop transfer function. Find the difference of settling time duration during step response, if this system would be closed-loop. R(s) a. 0.5635 b.

Given open-loop transfer function. Find the difference of settling time duration during

Given open-loop transfer function. Find the difference of settling time duration during step response, if this system would be closed-loop. R(s) a. 0.5635 b. 0.5835 C. 0.5735 d. 0.5935 24 s3+9s+26s+24 C(s)

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

According to research on spoon use in infancy, it can take __for infants to master spoon use. 1mmonth, 2-3 months, 6-8 months, 4-6 months

Write a short paragraph about "What should a hiring process be?" In HRM

Read the Citizens Guide to the Federal Budget that is posted in this week's module. Review the federal budget historical tables at the following website and provide your answers to the following...

The steering input controls the lateral motion of the vehicle (see Figure 1). The automated vehicle steering control system uses information about the vehicle position relative to the center of the...

This is a desktop based activity focussing on deriving the characteristic equation of DC motor followed by obtaining the behaviour of system in time and frequency domains using computer simulation...

Question 1 : Step response of a second order process is given as follows. Step Response Figure 1 : Step response of a second order process. a . Calculate the overshoot, peak time and gain of the...

In Problem 67, Chapter 7 (Figure P7.31), the block diagram of a cascade scheme for the speed control of an HEV (Preitl, 2007) was represented as a unity feedback system. In that diagram the output of...

Appendix G: (Not required information but I put it here incase it might help) b. Build a Simulink program based on the transfer function in Eq. (2-8) with R= 10k12 and C = 10uF. to conduct...

Background The system to be studied involves the positioning of a mechanical load characterised by mass and frictional damping. The load is moved by a hydraulic actuator which responds to a control...

-----------I need answer f,g------------ Problem 1. Consider that a feedback system has the open-loop poles of -4,-1 j and no zeros (only K). (a) Sketch the root-locus of the system. (b) Find the...

Holiday Pty Ltd was incorporated on 1 July 2018 (costs of incorporation were $2,500) and conducted a travel agency business which incurred tax losses of $55,000 and $15,000 in the years ended 30 June...

Gloria Modine is reviewing the principle of segregation of duties. What are the two common applications of this principle?

C t o represent a constant. x x + 3 2 d x =

Consider the process below: Water In Steam Combustor Gas Out Gas In Generator Combustor exit Steam Out A methane (CH.) and air mixture is burnt in the combustor then the heat is recovered to produce...

A companys zero coupon bond issue matures in 16 years and has a yield to maturity of 10.60%. Each zero has a face value of $1,000 and there are 4,000 of the bonds outstanding. If the market values...

QUESTION 1 A multi-faceted financial system which includes non-bank financial institutions (NBFIS), can protect economies from financial shocks and recover from those shocks. Discuss the significance...

Determine for each, whether the interest parity condition holds or not, if Ee$/euro = 1.10 Interest Rate for the Dollar, Interest Rate for the Euro R$ R 0.04 0.07 0.08 0.09 0.2 0.1 0.12 0 0.02 0.08...

Design a minimum-mass symmetric three-bar truss (the area of member 1 and that of member 3 are the same) to support a load P, as was shown in Fig. 2.9. The following notation may be used: Pu = P cos...

c. What is the probability that lifetime is at least 200? Greater than 200?

b. What is the probability that lifetime is at most 100?

77. The authors of the paper from which the data in Exercise 1.27 was extracted suggested that a reasonable probability model for drill lifetime was a lognormal distribution with 4.5 and .8.