Question: Given the Mohr's Circle and element shown below. a . Plot the Mohr's Circle? b . What are the minimum and maximum principal stresses? c

Given the Mohr's Circle and element shown below.
a. Plot the Mohr's Circle?
b. What are the minimum and maximum principal stresses?
c. What is the maximum shear stress?
d. When the shear stress is a maximum what will the compressive stresses be?
e. To put the element in a state of 0 shear stress how far must the element be rotated and in what direction?
f. What is the shear stress on a plane 30CCW from horizontal?
Given the Mohr's Circle and element shown below.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Q . 2 . An element in plane stress in subjected to stresses x , y and x y ( see the figure ) . Using Mohr's circle, a ) Determine the principle stresses. ( 1 0 % ) b ) Determine the maximum shear...

Q:

Assume that for stress measurement around a cavern, a 4 5 degree rosette ( or vibrating wire strain gage rods ) mounted at 4 5 deg. angular increment is installed on a polished section of the end...

Q:

machine element is made of an alloy with Yield strength of 200 Mpa and fracture strain is 0.08. A machine element is characterized by the normal stress components as shown in the figure. The Answer...

Q:

(1) For the given stress element shown below: a) Construct Mohr's stress circle using a suitathe Construct Mohr's stress circle using a suitatie scale and determine the maximum and minimum principal...

Q:

A drained shearbox test was carried out on a sample of saturated sand. The normal effective stress of 4 1 . 6 7 kPa was constant throughout the test, and the initial sample dimensions were 6 0 mm x 6...

Q:

Example 3 . 4 Mohr Circle Extension For the soil profile given below, assume that the moist unit weight, m 0 is 1 2 0 p c f and the saturated unit weight g a t , is 1 2 5 p c f . For an element shown...

Q:

( a ) Sketch the element for which the normal and shearing stresses are known or have been calculated ( Figure 8 . 4 ) . Show the actual directions of the stresses. 3 Laboratory 8 Civ E 2 7 0 ( b )...

Q:

Question 3 : For an element in a state of plane stress subjected to the normal and shear stresses [ 2 0 marks ] shown below, use the Mohr's circle solution ( not the transformation equations ) to...

Q:

5 - 5 Repeat Problem 5 - 1 by first plotting the failure loci in the A , B plane to scale; then, for each stress state, plot the load line and by graphical measurement estimate the factors of safety....

Q:

Problem # 4 : ( 3 0 points ) At a point in a structural member, the normal stresses and the shear stress are shown in Figure 4 . In an x - y coordinate system ( not shown in the figure ) , the...

Q:

100 percent transmittance 80 60 40 20 0 2.6 2.8 3 wavelength, micrometers 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12 13 14 1516 3800 3400 3000 2600 2200 2000 1800 1600 1400 1200 1000 wavenumber, cm Which...

Q:

(a) What is the ratio of HCO3 - to H2CO3 in blood of pH 7.4? (b) What is the ratio of HCO3- to H2CO3 in an exhausted marathon runner whose blood pH is 7.1?

Q:

Based on this information, what was the net income or loss for the year? On January 1, 2015, a new business was started with an initial investment of $12,000 in cash and $8,500 in equipment. During...

Q:

Victorian oshc Procedure/s for: Handling, preparation, processing, display, packaging and storing requirements of materials and products used in the food handling area. The national, state/territory...