Question: A solid cylindrical slug made of 410 stress steel is 200 mm in diameter and 300 mm high it is reduced in height by 70%

A solid cylindrical slug made of 410 stress steel is 200 mm in diameter and 300 mm high it is reduced in height by 70% at room temperature by open die forging with flat dies. Assuming that the coefficient of friction is 0.25, calculate the forging force at the end of the stroke.

Step by Step Solution

★★★★★

3.38 Rating (151 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

o calculate the forging force required to reduce the height of the solid cylindrical ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Programming Questions!

Mr. H turns on his fan and the three blades (25 cm each) experience a ccw angular acceleration of 3 rad/s/s. What is the angular displacement after the first 20 seconds. ? At the end of the day when...

The following additional information is available for the Dr. Ivan and Irene Incisor family from Chapters 1-5. Ivan's grandfather died and left a portfolio of municipal bonds. In 2012, they pay Ivan...

Planning is one of the most important management functions in any business. A front office managers first step in planning should involve determine the departments goals. Planning also includes...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

1. A solid cylindrical workpiece, made of 1020 steel, has a height of 120 mm, and a diameter of 100mm. It is to be reduced in height by 10% by forging. Let the coefficient of friction be 0.15....

A steel tube encases a solid cylindrical bar made of high - density polyethylene. The polyethylene has a diameter d 1 = 4 . 9 i n . and the steel tube has inner diameter d 2 = 5 . 1 i n . The...

Forging: Q 4 ) Calculate the forging force for a solid, cylindrical workpiece made of 1 0 2 0 steel ( K = 7 3 7 MPa and n = 0 . 1 9 ) that is 9 0 mm high and 1 2 5 mm in diameter and is to be reduced...

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Oliver has a mass of 76.2 kg. He is riding in an elevator that has a downward acceleration of 1.37 m/s2. With what magnitude force does the elevator floor push upward on Oliver?

Identify which of the following items are included in the calculation of cash flow before taxes (CFBT): operating expenses salvage value , depreciation, initial investment, gross income, tax rate.

Which technological change caused suburbs to develop away from central business districts in North American cities? Question 21Select one: a. The invention of the telegraph b. The invention of...

In an RLC series circuit the phase angle between the current and voltages is 30 degrees. If the AC frequency doubles, what is the resulting phase angle? a. 30 degrees b. more than 30 degrees c. less...

A single circuit 3 phase transmission transposed line is composed of four ACSR 1,272,000 cmil conductor per phase with horizontal configuration as shown below. The bundle spacing is 45 cm. The...

Fault analysis: Consider the following five-bus power system (A-Y phase shifts are negligible. Prefault voltage is 1.08 per unit). Figure 2: A five-bus power system. Gener- ator G1: 100 MVA, 10 kV,...

the intensity of light from a lightbulb is 10 w/m^2 at a distance of 0.50 from the bulb. what is the intensity across the room at a distance of 3.5m?

What are the advantages of a simulation or field study for experimental research?

Falling-cylinder viscometer (see Fig. 2C.4) A falling-cylinder viscometer consists of a long vertical cylindrical container (radius R), capped at both ends, with a solid cylindrical slug (radius KR)....

The drawing shows a solid cylindrical rod made from a center cylinder of lead and an outer concentric jacket of copper. Except for its ends, the rod is insulated (not shown), so that the loss of heat...

A long slender solid cylindrical rod made of copper is 2 cm in diameter. It is taken out of a liquid nitrogen bath at 77 K and exposed to a stream of warm air at a temperature of 50 C. Neglect...

Homework Set 1 17.33: Estimate the maximum tonnage required to compact a brass slug 3.0 inches in diameter. Would the height of the slug make any difference in your answer? Explain your reasoning....

A cylindrical slug that has a diameter of 1 in. and is 1 in. high is placed at the center of a 2-in.-diameter cavity in a rigid die. The slug is surrounded by a compressible matrix, the pressure of...

A hollow cylindrical rod (rod 1) and a solid cylindrical rod (rod 2) are made of the same material. The two rods have the same length and the same outer radius. If the same compressional force is...