Question: In a geometric tolerance frame, if there is no modifier shown next to the geometric tolerance, what modifier is understood? a. MMC b. LMC

In a geometric tolerance frame, if there is no modifier shown next to the geometric tolerance, what modifier

In a geometric tolerance frame, if there is no modifier shown next to the geometric tolerance, what modifier is understood? a. MMC b. LMC C. P d. RFS

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

In the context of a geometric tolerance frame according to the ASME Y... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Consider a project of manufacturing and selling high-end smartwatches to wealthy customers. The length of the project is 10 years. The industry demand for high-end smartwatches next year will be 1...

Q:

In fewer than 25 words explain what industry means to you in terms of competitive strategy Explain what went into your brief definition What did you have to include and what did you end up leaving...

Q:

In the system shown in Fig. 5.54, block A has mass mA, block B has mass mB' and the rope connecting them has a nonzero mass mole. The rope has a total length L, and the pulley has a very small...

Q:

What are the dimensions of environment and how might they influence human behavior? How does a thorough understanding of the dimensions of environment support successful assessment and intervention...

Q:

can you help me with my cnc midterm asap please! thank you! 1) Which of the following ASME Y14.5 symbols represents a controlled radius? a. V b. R c. CR d. D 2) What does the diagram on the right...

Q:

1 ) \ ( ( 0 . 5 \ ) points ) Th is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 2 ) ( 0 . 5 points ) The is the condition in...

Q:

ISE 2 3 6 0 Design for Manufacturing Lecture Assignment 4 Due date: Refer to the syllabus. ( 1 ) Add geometric tolerances to the drawing below that specify a flatness control of . 0 0 5 for the top...

Q:

( 2 ) Based on the tolerances specified in 2 . 1 , is the part shown below an acceptable part? Why or why not? Answer the following questions using the drawing below: What is the MMC ? What is the...

Q:

1 . What type of condition is applied when a part contains its largest amount of material? a . Allowable condition b . Least material condition c . Maximum material condition d . Regardless of...

Q:

Write a C++ code that will ask the user to enter an employee performance. Using Switch statement, the code then should output the following: If the performance is 5, Outstanding If the performance is...

Q:

A survey of the world's nations in 2014 shows a strong positive correlation between percentage of the country using smart phones and life expectancy in years at birth. a) Does this mean that smart...

Q:

Sammamish Brick, Inc., manufactures bricks using clay deposits on the companys property. Raw clays are blended and then extruded into molds to form unfired bricks. The unfired bricks are then stacked...

Q:

For Milestone One, select and submit a product category and product brands. First, identify the product category to be evaluated. Once the product category is selected and described, identify which...

Q:

For each of the following determine for each variable x the l x. it is bound to. I have numbered the variables and the abstraction. The variables are numbered using Arabic numerals and the...

Q:

Design an LM348 op-amp IC as a three-stage amplifier (shown in Figure 1) that will provide the outputs 10, 20, and 50 times larger than the input. In your design, use the feedback resistor of Rf=500...

Q:

The equation: (x-pi)*sin(x)=(x-2) has two roots in the interval 14 . I) Explain why it is an unconditional problem to find these roots numerically. II) If one uses Newton's method to solve the...

Q:

How you make decisions would be seen in which type?Group of answer choicesExtrovertsSensingThinkingJudging

Q:

Suppose you and I have the same homothetic tastes over x1 and x2, and our endowments of the two goods are EM = (eM1, eM2) for me and EY = (eY1, eY2) for you. A (a) Suppose throughout that, when x1 =...

Q:

Social Norms and Private Actions: When asked to explain our actions, we sometimes simply respond by saying it was the right thing to do. The concept of the right thing to do is one that is often...

Q:

Suppose you have $400,000 to spend on a house and other goods (denominated in dollars). A. The price of 1 square foot of housing is $100 and you choose to purchase your optimally sized house at 2000...

Q:

An experiment was performed to compare the fracture toughness of high-purity 18 Ni maraging steel with commercial-purity steel of the same type (Corrosion Science, 1971: 723736). For specimens, the...

Q:

5.74. Find the standard error of the sample proportion when tt 0 or tt 1. What does this reflect?

Q:

Tensile-strength tests were carried out on two different grades of wire rod (Fluidized Bed Patenting of Wire Rods, Wire J., June 1977: 5661), resulting in the accompanying data. Sample Sample Mean...