Question: (manufacturing process) please solve this question by computer not handwritten, also different solution. Turning is performed on a work material with shear strength of 250

(manufacturing process)
please solve this question by computer not handwritten, also different solution.

Turning is performed on a work material with shear strength of 250 MPa. The following conditions are used: v = 4.0 m/s, f = 0.25 mm/rev, d = 3.0 mm, and rake angle = 9 in the direction of chip flow. The %3! resulting chip ratio = 0.5. Using the orthogonal model as an approximation of turning, determine: (a) the shear plane angle; (b) the shear force; (c) cutting force and feed force; (d) shear stress; (e) friction angle; (f) friction coefficient; (g) Discuss the effect of increasing shear angle on shear force and shear stress. Chip Tool R. Work

Step by Step Solution

★★★★★

3.35 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

To solve this problem we will use the orthogonal cutting model Here are the steps Given Data Cutting speed v 40 textms Feed rate f 025 textmmrev Depth ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

In one project, they have asked you to determine the Aluminium density at 650C. Keep in mind that aluminium has a density of 2.70 g/cm' at room temperature (20C). Use data in the Table 1 as a...

(manufacturing process) please solve this question by computer not handwritten. Around disk of 150 mm diameter is to be blanked from a strip of 3.2 mm, half-hard cold rolled steel whose shear...

Using the information below, determine the Net Income for Tax Purposes for The Company LTD. Ensure your answer includes any supporting calculations and CCA Schedules. Excerpt from Financial...

Write a thesis statement on World Political History Topic Question: Rwandan Genocide in which you need to address the following: In depth, what was the main reason that led to the Rwandan Genocide?...

Suppose you will perform a test to determine whether there is sufficient evidence to support a claim of a linear correlation between two variables. Find the critical values of r given the number of...

1. What is the difference between the NLRA and the LaborManagement Relations Act? 2. Why has the NLRB recently been thrust into the forefront with regard to labor relations? 3. What is typically...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Please quality check my solutions for this advanced heat transfer problem. Show all work. Thank you. All original documents are located at the bottom. 3.9 COMPACT HEAT EXCHANGERS 3.9.10-1 3.9.10...

2 0 . 5 ( A ) ( USCS units ) A turning operation is performed using a rake angle of 1 5 . Cutting speed = 2 0 0 f t m i n , feed = 0 . 0 1 2 i n r e v , and depth of cut = 0 . 1 0 0 i n . The chip...

Republic of Iraq Ministry of Higher Education and Scientific Research University of Technology Chemical Engineering Department MODELING AND SIMULATION OF FCC RISERS A RESEARCH SUBMITTED TO THE...

How would you explain the concept of management vs leadership to someone else? Give an example of a manager that you thought was an excellent leader. What qualities or actions did this person take to...

Project Assignment 1 For this week we will log into the Planview Daptiv PPM tool, familiarize ourselves with navigating within the tool, and begin building out a project. We will take the fictious...

A person is creating small parts for a project. The work is boring but necessary. His boss hopes to speed up this activity by hiring another skilled employee, and in doing SO Will: Elevate the...

Mr. Vinayak is working as Chief Personnel Officer in Bank of Maharashtra. The following are the particulars of his income : Basic salary Rs.25000 p.m DA Rs.4000 p.m Special Executive allowance -...

Mr. Cruz has been working on a research related to job satisfaction of different employees from different departments. Since the company has hundreds of employees in total the number of employees per...

a. Suppose, as a result of various dynamic factors associated with exposure to international competition, Albania's economy grew, and is now represented by the rightmost production possibility...

Is this item considered to be part of gross income for lax year 2 0 2 2 ? Alimory executed 9 / 2 8 / 2 0 1 9

What exactly is a prima facie duty? How does an ethic of prima facie duties differ from monistic and absolutist ethical theories?

A fixed quantity of gas undergoes the reversible changes illustrated in the pV diagram in Fig. 12.22. How much work is done in each process? 4. 1.00 x 105 0.50 x 105 3 0.25 0.50 0.75 1.00 Volume im3)

A circular piece is cut from an aluminum sheet at room temperature. (a) When the sheet is then placed in an oven, will the hole (1) get larger, (2) get smaller, or (3) remain the same? Why? (b) If...

A rigid container contains 1.0 mol of an ideal gas that slowly receives 2.0 x 104J of heat. (a) The work done by the gas is (1) positive, (2) zero, (3) negative. Why? (b) What is the change in the...

The Cowichan Regional District borrowed $500,000 through the Provincial Finance Authority to purchase fire-fighting equipment. At the end of every six months, the regional district must make a...

A $1000, 9.5% coupon Government of Canada bond has 10 years remaining until its maturity. It is currently priced at 108.25 (percent of face value). a. What is the bonds yield to maturity? b. If the...

Rocky Mountain Bus Tours needs an additional bus for three years. It can lease a bus for $2100 payable at the beginning of each month, or it can buy a similar bus for $120,000, using financing at the...