Question: - Problem 1 (30 pts) A process is in control with = 70.1 and 5 = 70.1 and 5 = 1.2. The process specifications are

- Problem 1 (30 pts) A process is in control with

- Problem 1 (30 pts) A process is in control with = 70.1 and 5 = 70.1 and 5 = 1.2. The process specifications are given as 70+3.2. The sample size n= 6. Assume that the quality characteristic is normally distributed. a) Design the center line and control limits for x-bar chart and s chart. b) Estimate the standard deviation of the process. c) Estimate the process capability ratio Cp. d) What's the defective rate the process is producing or how much is process fallout of the specification limits? e) How much could process fallout be reduced by shifting the process mean from 70.1 to the nominal dimension

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Hi, I attached question for python. please help us solve that. thanks ## Introduction OpenData sources are growing in number. Many governments have "OpenData" initiatives that provide portions of...

1 18 1. Vacuum pumps are being audited to determine if the process is in control and also capable of meeting the customer specifications. Samples of size 5 are taken cach hour of the day and tested...

1. Vacuum pumps are being audited to determine if the process is in control and also capable of meeting the customer specifications. Samples of size n=5 are taken each hour of the day and tested with...

Problem #3 (30 pts) Plastic keychains are produced in a company named PUNE Plastics. The plastic material is first molded and then trimmed to the required shape. The cure times (which is the time for...

Specifications for a part for a 3-D printer state that the part should weigh between 24 and 25 ounces. The process that produces the parts has a mean of 24.5 ounces and a standard deviation of .2...

Please help me Based on the given dataset: Q1. What are the Upper and lower Control Limits in your X-Chart? (p. 251) Show your work and calculations. Assume that the population standard deviation (8)...

Please, answer the three questions below using Excel or spreadsheet. Thank you! See the Factors worksheet below to answer question #1 Problem \#3 (30 pts) Bag clips are manufactured at Keep it Fresh....

Please show formulas on excel please Problem \#3 (30 pts) Bag clips are manufactured at Keep it Fresh. The clip material is first molded and then trimmed to the required shape. The time it takes for...

problem 1 parts 1 through 5. ill be sure to give you a thumbs up 1. (9 points) Sample Sample Sample Sample Sample 1 2 3 4 5 Obs.1 16.4 15.97 15.91 16.2 15.87 Obs.2 16.11 16.1 16 16.21 16.21 Obs.3...

Refer to the table Factors for Computing Control Chart Limits (3 sigma) for this problem. Pet Products, Inc., caters to the growing market for cat supplies, with a full line of products ranging from...

Due to temporary weather patterns, suppose production in the agricultural sector increases. a. Given the various shifters presented in the book/lecture notes, which curve(s) shifts first and why?...

If your income after taxes is $28,000 per year, and you expect to pay about $100 per month for utilities, about how much can you afford to spend on monthly rental payments?

7. In the figure, the angle of elevation of the top of a wrtical tower PQ from a point A is 30. The foot of the tower Q, is on the same horizontal plane a as A and B. Given that AB=60 m, LRAQ-45 and...

Case Greenbuilders Pte Lid ("GPL") is a local construction company which specialises in providing bespoke Design and Build construction services for private residential homes that are designed to be...