Question: Problem 4 . Wire AC is made of A - 3 6 steel having a yielding stress y = 2 5 0 MPa and a

Problem 4.
Wire AC is made of A-36 steel having a yielding stress y=250MPa and a modulus of elasticity
E=200GPa and a strain hardening slope of 2000 MPa and rupture at R=0.2mmmm. Wires AB
and AD are made of A-992 steel assumed to have elasto-plastic behavior having a yielding stress
y=350MPa and a modulus of elasticity E=200GPa. All bar diameters are 2-mm.
Determine the load and vertical displacement at first yield
Determine the load and vertical displacement at ultimate
Plz draw the FBD and slove it step by step
Problem 4 . Wire AC is made of A - 3 6 steel

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Each arm comprises a horizontal beam made from an AISI651 stainless steel tube (see Table 1 for the material properties) of length L = 35 mm, inner diameter d = 375 m and outer diameter do = 575 m,...

Q:

Problem 8 For most dispersion-hardened alloys, usually it is reasonable to assume that all particles are the same size. However, this is not always accurate. Sometimes there is a range of particle...

Q:

Instructions: For problems 4 and 5 use the table provided below: Table 6.1 Room-Temperature Elastic and Shear Moduli and Poisson's Ratiofor Various Metal Alloys Modulus of Shear Modulus Elasticity...

Q:

Problem 8 For most dispersion-hardened alloys, usually it is reasonable to assume that all particles are the same size. However, this is not always accurate. Sometimes there is a range of particle...

Q:

10. Question 10 [10 marks total] a. In your own words, describe the difference between elastic deformation and plastic deformation. [2] The stress-strain curve for a material is shown below. 2000...

Q:

9:46 1

Q:

4 to O Problem 4 28 pts A 100 mm long rectangular bar with a 10 mm x10 mm cross section shown here is made of brass The bar is deformed elastically in tension with a force of 30 000 N With the...

Q:

Problem 1 Multiple Choice Problems (Check all that apply (20 pt) I. Which of the polymers may be recycled and why (2 pts) (a) Billiard balls made from phenol-formaldehyde resin (b) Plastic wrap (c)...

Q:

Risk Analysis and Management of Construction and Operations in Offshore Wind Power Project Abstract: Many countries have increased the use of renewable energy and strongly promoted offshore wind...

Q:

Question 1 (50%) A solid shaft of 100 mm diameter has a strain gauge mounted on the surface at 30 to the axis of the shaft at point O, as shown in Figure 1. In service an axial force P = 500 kN and a...

Q:

Sunrise Coffee Company roasts and packs coffee beans. The process begins in the Roasting Department. From the Roasting Department, the coffee beans are transferred to the Packing Department. The...

Q:

Exercise 5 lists the amounts of carbon monoxide emissions, and listed below are the amounts (million metric tons) of nitrous oxide emissions in the United States for the same ten-year period as in...

Q:

A corporation's bank account has $9,389 in it when the treasurer writes checks for $3,424, $4,199, and $1,823. Then deposits of $1,958 and $2,260 are made. How much is in the account? Is it...

Q:

The management of Shatner Manufacturing Company is trying to decide whether to continue manufacturing a part or to buy it from an outside supplier. The part, called CISCO is a component of the...