Question: Question 2 In an orthogonal cutting operation, the tool has a rake angle = 1 5 degrees. The chip thickness before the cut =

Question 2
"In an orthogonal cutting operation, the tool has a rake angle =15 degrees. The chip thickness before the cut =0.23 mm and the cut
yields a deformed chip thickness =0.64mm. Calculate the shear strain for the operation. "
Question 2 " In an orthogonal cutting operation,

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

In an orthogonal cutting operation, the tool has a rake angle = of 15. The chip thickness before the cut = 0.30 mm and the cut yields a deformed chip thickness = 0.65 mm. Calculate (a) the shear...

Q:

This is a subjective question, hence you have to write your answer in the Text-Field given below. (a) Using a neat figure show continuous with built-up edge chip formation in metal cutting. Explain...

Q:

In an orthogonal cutting operation, the following data has been observed - Uncut chip thickness - 0 . 1 5 0 mm , Width of cut 6 mm , Cutting speed 5 m / s , Rake angle - 1 0 0 , Cutting force - 5 0 0...

Q:

Consider the straight turning operation of a AISI 1 0 1 0 steel bar with a tool with a rake angle of 5 and a clearance angle of 3 , using the following operating parameters: cutting speed is 3 1 5 m...

Q:

The shear strength of a certain work material = 5 0 , 0 0 0 lb / in 2 . An orthogonal cutting operation as illustrated in the figure below is performed using a tool with rake angle = 2 0 \ deg at a...

Q:

An orthogonal cutting operation is being carried out under the following conditions: to = 0.1 mm, tc = 0.2 mm, width of cut = 5 mm, cutting speed V = 2 m/s, rake angle = 10, Fc = 500 N, and Ft = 200...

Q:

Shear strength: The cutting force and thrust force have been measured in an orthogonal cutting operation to be 301 lb and 291 lb, respectively. The rake angle = 12, width of cut = 0.400 in, chip...

Q:

An orthogonal cutting operation is being carried out under the following conditions: to = 0 . 1 mm , tc = 0 . 2 mm , width of cut = 5 mm , V = 2 m / s , rake angle = 1 0 0 , Fc = 5 0 0 N , and Ft = 2...

Q:

chose the most correct answer for the following 1. The rake angle in a twist drill... A. Varies from minimum near the dead center to a maximum as the periphery. B. Is maximum at the dead center and...

Q:

If the growth of a population follows the logistic model but is subject to "harvesting" (such as hunting or fishing), the model Becomes (a) Show that when the harvest rate h is constant, a maximum...

Q:

Write code on Program Quartus represent function B(P, Z, A) =(AZ) +(A+Z) +( P bar + A) Material LabLogic Codes

Q:

percent and a standard deviation of 2 1 . 2 percent. In any one given year, you have a 9 5 percent chance that you wil not lose more than q , percent nor eam more than q , percent on this stock. - 2...

Q:

Sugiera cmo se puede utilizar el compromiso directo de losaccionistas con los gerentes y la remuneracin de la gerencia paragarantizar que los gerentes operen en el mejor inters de losaccionis 1 answer