The Admin wanted to check PVST setting only for VLAN 1 on the switch. He/She typed...

Transcribed Image Text:

The Admin wanted to check PVST setting only for VLAN 1 on the switch. He/She typed the following command and the command received an error. Re-type the right command in the blank. Note: Only type the corrected command with no prompt and no explanation and it must be an exact matching answer. Type the command in a complete word. Switch#show spanning-tree interface vlan 1 Answer: Refer to the graph: Please read the questions carefully and fill the blanks from the provided table: a. VLAN 1, VLAN 10, and VLAN 30 are set on all switches. Which protocol or service supposed to be running between the switches? b. SW2 connected to PC2. Which protocol or service supposed to be running between SW2 and PC2 to forward the frame? Note: Only type the correct exact-match keyword answer as in the table. Trunk RSTP VLAN |EtherChannel STP Access Dynamic RPVST PC1 PC4 5 SW1 SW4 == SW2 ||| ||| ||| SW3 PC2 PC3 Re-type the following command in the correct format. Note: Only type the corrected command with no prompt and no explanation and it must be an exact matching answer. Type the command in a complete word. Router(config)#deny host 10.0.0.2 in access-list 10 Answer: Refer to the network shown in the figure. You are looking to set standard numbered ACL rules at router R3 to accept the traffic from PC3 and discard the traffic from all other hosts of the subnetwork of PC3 and allow all other remaining traffic. In the following configuration enter the missing command. Note: Only type the command with no prompt and it must be an exact matching answer. Type the command in a complete word. R3(config)#access-list 1 permit 10.3.0.10 R3(config)# R3(config)#access-list 1 permit any R3(config)#interface s0/0/1 R3(config-if)#ip access-group 1 in 10.1.0.0/16 PC1 .10, Fa0 .1, G0/0 R1 .1, G0/1 .10, Fa0 D PC2 10.2.0.0/16 10.6.0.4/30 .5, S0/0/0 10.3.0.0/16 PC3 .6, S0/0/1 .10, Fa0 .1, G0/0 R2 10.6.0.8/30 .9, S0/0/0 .10, S0/0/1 10.4.0.0/16 Ser1 .10, Fa0 I.1, G0/0 R3 .1, G0/1 I.10, Fa0 Ser2 10.5.0.0/16 Fix the following command to give access to all ip packets from the specified source subnetwork. Note: Only type the corrected command with no prompt and it must be an exact matching answer. Type the command in a complete word. Router(config)#access-list 10 permit 10.16.0.0 255.240.0.0 many Router(config)# The Admin wanted to check PVST setting only for VLAN 1 on the switch. He/She typed the following command and the command received an error. Re-type the right command in the blank. Note: Only type the corrected command with no prompt and no explanation and it must be an exact matching answer. Type the command in a complete word. Switch#show spanning-tree interface vlan 1 Answer: Refer to the graph: Please read the questions carefully and fill the blanks from the provided table: a. VLAN 1, VLAN 10, and VLAN 30 are set on all switches. Which protocol or service supposed to be running between the switches? b. SW2 connected to PC2. Which protocol or service supposed to be running between SW2 and PC2 to forward the frame? Note: Only type the correct exact-match keyword answer as in the table. Trunk RSTP VLAN |EtherChannel STP Access Dynamic RPVST PC1 PC4 5 SW1 SW4 == SW2 ||| ||| ||| SW3 PC2 PC3 Re-type the following command in the correct format. Note: Only type the corrected command with no prompt and no explanation and it must be an exact matching answer. Type the command in a complete word. Router(config)#deny host 10.0.0.2 in access-list 10 Answer: Refer to the network shown in the figure. You are looking to set standard numbered ACL rules at router R3 to accept the traffic from PC3 and discard the traffic from all other hosts of the subnetwork of PC3 and allow all other remaining traffic. In the following configuration enter the missing command. Note: Only type the command with no prompt and it must be an exact matching answer. Type the command in a complete word. R3(config)#access-list 1 permit 10.3.0.10 R3(config)# R3(config)#access-list 1 permit any R3(config)#interface s0/0/1 R3(config-if)#ip access-group 1 in 10.1.0.0/16 PC1 .10, Fa0 .1, G0/0 R1 .1, G0/1 .10, Fa0 D PC2 10.2.0.0/16 10.6.0.4/30 .5, S0/0/0 10.3.0.0/16 PC3 .6, S0/0/1 .10, Fa0 .1, G0/0 R2 10.6.0.8/30 .9, S0/0/0 .10, S0/0/1 10.4.0.0/16 Ser1 .10, Fa0 I.1, G0/0 R3 .1, G0/1 I.10, Fa0 Ser2 10.5.0.0/16 Fix the following command to give access to all ip packets from the specified source subnetwork. Note: Only type the corrected command with no prompt and it must be an exact matching answer. Type the command in a complete word. Router(config)#access-list 10 permit 10.16.0.0 255.240.0.0 many Router(config)#